සහයෝගීතාව
කලාව
රූපලාවණ්‍ය සහ සුවතාව
ශිල්පය
සංස්කෘතිය සහ ඉතිහාසය
විනෝදාස්වාදය
පරිසරය
ආහාර සහ පාන
ප්‍රතිලෝම ඉංජිනේරු
විද්‍යාවන්
ක්‍රීඩා
තාක්ෂණය
පැළඳිය හැකි
Steel Needle: Pointed, Eyed, Hardened in Oil and Tempered
Forge

නිර්මාතෘ

Forge

18. ඔක්තෝබර් 2026NO
23
0
0
0
0

Steel Needle: Pointed, Eyed, Hardened in Oil and Tempered

Needles are made from good steel wire: cut, straightened, pointed, flattened and pierced for the eye, hardened by heating and plunging into oil, then tempered back to a springy hardness, scoured and polished (Bucknall Smith, A Treatise upon Wire, 1891). This is the same sequence by hand, one heavy needle at a time from piano wire; the hand methods and sizes are ours. The picture: steel sewing needles (Wikimedia Commons).
මධ්‍යම
Half a day

උපදෙස්

1

Cut, soften and straighten

Cut 70 mm of 1.2 mm piano wire. Heat it to red in the forge and let it cool slowly in the ashes so it can be filed and drilled, then roll it straight on the anvil.

මෙම පියවර සඳහා ද්‍රව්‍ය:

පියානෝ කම්බියපියානෝ කම්බිය70 mm

අවශ්‍ය මෙවලම්:

විකර්ණ කම්බි කපන අඬුවවිකර්ණ කම්බි කපන අඬුව
කම්මල් උදුනකම්මල් උදුන
සිහින් මුඛ අඬුසිහින් මුඛ අඬු
නියන (ඇන්විලය)නියන (ඇන්විලය)
2

Point

Clamp it in the vise and file a long, even taper to a sharp point, turning the wire as you go.

අවශ්‍ය මෙවලම්:

කටු කට්ටලයකටු කට්ටලය
බංකු තද කරන්නාබංකු තද කරන්නා
ආරක්ෂිත කණ්ණාඩිආරක්ෂිත කණ්ණාඩි
3

Flatten and pierce the eye

Flatten the head end slightly on the anvil, drill the eye through the flat with the finest bit, then file off the burrs and round the head.

අවශ්‍ය මෙවලම්:

නියන (ඇන්විලය)නියන (ඇන්විලය)
හරස් කුඤ්ඤ හිසක් සහිත මිටියහරස් කුඤ්ඤ හිසක් සහිත මිටිය
අත් විදුමඅත් විදුම
කටු කට්ටලයකටු කට්ටලය
බංකු තද කරන්නාබංකු තද කරන්නා
ආරක්ෂිත කණ්ණාඩිආරක්ෂිත කණ්ණාඩි
4

Harden in oil

Heat the needle evenly to red and plunge it into the oil. It is now glass-hard and brittle.

අවශ්‍ය මෙවලම්:

කම්මල් උදුනකම්මල් උදුන
සිහින් මුඛ අඬුසිහින් මුඛ අඬු
තෙල් සහිත නිවීමේ ටැංකියතෙල් සහිත නිවීමේ ටැංකිය
ආරක්ෂිත කණ්ණාඩිආරක්ෂිත කණ්ණාඩි
5

Temper

Reheat it in the oven to about 600 °F (315 °C) and let it cool slowly to a springy temper. If it came out crooked, straighten it with light blows of a small hammer on the anvil.

අවශ්‍ය මෙවලම්:

තාප පිරියම් උදුනතාප පිරියම් උදුන
කියවීමක් සහිත තාපයුග්මයකියවීමක් සහිත තාපයුග්මය
නියන (ඇන්විලය)නියන (ඇන්විලය)
හරස් කුඤ්ඤ හිසක් සහිත මිටියහරස් කුඤ්ඤ හිසක් සහිත මිටිය
6

Scour and polish

Scour it bright with emery cloth, a little oil and soap. Wash it in hot water, dry it in sawdust, touch up the point, and polish it on the leather strop.

අවශ්‍ය මෙවලම්:

එමරි රෙද්දඑමරි රෙද්ද
ඔලිව් තෙල්ඔලිව් තෙල්
සබන්සබන්
කරත් කුඩුකරත් කුඩු
සම් මුවහත් පටියසම් මුවහත් පටිය
කටු කට්ටලයකටු කට්ටලය

ද්‍රව්‍ය

1

අවශ්‍ය මෙවලම්

17

මෙම සැලසුම සාදන්නේ

සම්බන්ධ බ්ලූප්‍රින්ට්

මෙම බ්ලූප්‍රින්ට් දැනුම බෙදා ගනී — ශිල්ප ක්‍රම, ද්‍රව්‍ය හෝ මූලධර්ම

CC0 පොදු වසම

මෙම බ්ලූප්‍රින්ට් CC0 යටතේ නිකුත් කර ඇත. ඔබට අවසර නොමැතිව පිටපත් කිරීම, වෙනස් කිරීම, බෙදා හැරීම සහ භාවිතා කිරීම කළ හැක.

බ්ලූප්‍රින්ට් හරහා නිෂ්පාදන මිලදී ගැනීමෙන් නිර්මාතෘට සහාය වන්න නිර්මාතෘ කොමිසම විකුණුම්කරුවන් විසින් නියම කළ, හෝ මෙම බ්ලූප්‍රින්ට්හි නව අනුවාදයක් සාදා ආදායම බෙදා ගැනීමට ඔබේ බ්ලූප්‍රින්ට්හි සම්බන්ධතාවයක් ලෙස ඇතුළත් කරන්න.

සාකච්ඡාව

(0)

පිවිසෙන්න සාකච්ඡාවට එක්වීමට

අදහස් පූරණය කරමින්...