အနုပညာ
အလှအပနှင့် ကျန်းမာရေး
လက်မှုအနုပညာ
ယဉ်ကျေးမှုနှင့် သမိုင်း
ဖျော်ဖြေရေး
ပတ်ဝန်းကျင်
အစားအစာနှင့် အချိုရည်
ပြောင်းပြန်အင်ဂျင်နီယာပညာ
သိပ္ပံပညာများ
အားကစား
နည်းပညာ
ဝတ်ဆင်နိုင်သောပစ္စည်းများ
Leather Strips and Straps
Tex

ဖန်တီးသူ

Tex

11. အောက်တိုဘာ 2026FO
၃၆
၀
၀
၀
၀

Leather Strips and Straps

Belts, handles, laces and hinges start as strips cut from a side of firm vegetable-tanned leather. A strap cutter holds the width while you draw it along a straight edge; the edges are then bevelled, sanded and burnished smooth with a little gum and friction so they do not fray or fuzz. Firm leather about 3–4 mm thick suits straps; thinner leather suits laces and binding strips.
အစပြု
1 hour

ညွှန်ကြားချက်များ

1

The leather

How the firm, vegetable-tanned leather is made.
2

Cut a straight edge

Lay the leather grain side up on the cutting mat and cut one long straight edge along the straightedge, following the backbone line where the leather is most even.

ဤအဆင့်အတွက် ကုန်ကြမ်းများ:

အပင်ဓာတ်ဖြင့်နယ်ထားသောသားရေအပင်ဓာတ်ဖြင့်နယ်ထားသောသားရေ0.1 sqm

လိုအပ်သော ကိရိယာများ:

ဖြောင့်သောအနားဖြောင့်သောအနား
အသုံးဝင်ဓားအသုံးဝင်ဓား
ကိုယ်တိုင်ပြန်ကောင်း ဖြတ်ခုံအခင်းကိုယ်တိုင်ပြန်ကောင်း ဖြတ်ခုံအခင်း
ဒစ်ဂျစ်တယ် ကာလီပါ ၆ လက်မဒစ်ဂျစ်တယ် ကာလီပါ ၆ လက်မ
3

Pull the strips

Set the strap cutter to the width, run its fence against the straight edge and pull it along the leather in one steady draw. Repeat for each strip.

လိုအပ်သော ကိရိယာများ:

သားရေကြိုးဖြတ်ကိရိယာသားရေကြိုးဖြတ်ကိရိယာ
တိုင်းတာရေးတိပ်တိုင်းတာရေးတိပ်
4

Bevel the edges

Run the edge beveler along both corners of each edge, front and back.

လိုအပ်သော ကိရိယာများ:

သားရေအနား ချောစက်သားရေအနား ချောစက်
5

Sand and burnish

Sand the edges smooth, dampen them with a little gum tragacanth in water, and rub hard with the wooden slicker until they shine. A touch of beeswax finishes them.

ဤအဆင့်အတွက် ကုန်ကြမ်းများ:

ထရာဂါကန့် ကော် (ကစ်ထရေ)ထရာဂါကန့် ကော် (ကစ်ထရေ)5 ဂရမ်
ရေရေ0.05 လီတာ
ပျားဖယောင်းပျားဖယောင်း5 ဂရမ်

လိုအပ်သော ကိရိယာများ:

သဲစက္ကူပြားသဲစက္ကူပြား
သားရေအနား ချောတိုက်ကိရိယာသားရေအနား ချောတိုက်ကိရိယာ
6

Punch and finish

Cut the ends to shape and punch any holes the strap needs.

လိုအပ်သော ကိရိယာများ:

သားရေဖောက်ကိရိယာအစုံသားရေဖောက်ကိရိယာအစုံ
အသုံးဝင်ဓားအသုံးဝင်ဓား
7

Troubleshooting

Strap cutting troubleshooting.

Flow

Loading...

ပစ္စည်းများ

4

လိုအပ်သော ကိရိယာများ

10

ဆက်စပ် အစီအစဉ်များ

ဤအစီအစဉ်များသည် အသိပညာမျှဝေသည် — နည်းပညာ၊ ပစ္စည်း သို့မဟုတ် မူများ

CC0 အများပိုင်

ဤအစီအစဉ်ကို CC0 အောက်တွင် ထုတ်ဝေထားသည်။ ခွင့်ပြုချက်မလိုဘဲ ကူးယူ၊ ပြင်ဆင်၊ ဖြန့်ဝေ နှင့် အသုံးပြုနိုင်သည်။

အစီအစဉ်မှတစ်ဆင့် ကုန်ပစ္စည်းများဝယ်ယူ၍ လက်မှုပညာရှင်ကို ပံ့ပိုးပါ လက်မှုပညာရှင် ကော်မရှင် ရောင်းချသူက သတ်မှတ်သည်၊ သို့မဟုတ် ဤအစီအစဉ်၏ ဗားရှင်းအသစ်ဖန်တီး၍ ဝင်ငွေခွဲဝေရန် သင့်အစီအစဉ်တွင် ချိတ်ဆက်မှုအဖြစ် ထည့်သွင်းပါ။

ဆွေးနွေးချက်

(0)

ဝင်ရောက် ဆွေးနွေးချက်တွင် ပါဝင်ရန်

မှတ်ချက်များ ရယူနေသည်...