အနုပညာ
အလှအပနှင့် ကျန်းမာရေး
လက်မှုအနုပညာ
ယဉ်ကျေးမှုနှင့် သမိုင်း
ဖျော်ဖြေရေး
ပတ်ဝန်းကျင်
အစားအစာနှင့် အချိုရည်
ပြောင်းပြန်အင်ဂျင်နီယာပညာ
သိပ္ပံပညာများ
အားကစား
နည်းပညာ
ဝတ်ဆင်နိုင်သောပစ္စည်းများ
Making a Coiled-Straw Bee Skep — The Traditional Beehive Before Wooden Boxes
The bee skep is the coiled-straw beehive that housed honeybees across Europe for roughly two thousand years, from antiquity into the 1800s, before wooden box hives replaced it. Using the same coiling technique as a straw basket, long rye straw is wound into a dome and stitched together with split cane. This blueprint builds a traditional skep by hand — from preparing the straw to the finished, weatherproofed hive ready to house a swarm.
အလယ်အလတ်
8
ညွှန်ကြားချက်များ
1
1
Harvest and clean long rye straw
Harvest and clean long rye straw
Cut long rye or wheat straw and strip off the seed heads and leaf sheaths, keeping the hollow stems long and unbroken for strong coils.
Materials for this step:
Rye Straw1 ထုပ်Tools needed:
Knife2
2
Split and soak the binding cane
Split and soak the binding cane
Split lengths of cane into thin flexible strips and soak them in water until pliable — these will sew the straw coils together.
Materials for this step:
Split Cane1 ထုပ်
Water3 လီတာTools needed:
Knife3
3
Make the girth gauge
Make the girth gauge
Form a small open ring about 2.5 cm across (the traditional 'girth', often a cow-horn tip). Straw fed through it keeps every coil the same thickness.
Tools needed:
Skep Girth Gauge4
4
Bind the crown
Bind the crown
Take a small handful of straw, bend it into a tight knot to form the top knob of the skep, and lash it firmly with a strip of split cane.
Materials for this step:
Rye Straw1 ထုပ်Split Cane1 မီတာTools needed:
Awl5
5
Feed straw into an even rope
Feed straw into an even rope
Pass straw through the girth to form a continuous rope of even thickness, adding a few stems at a time so the bundle never thins as you work.
Materials for this step:
Rye Straw1 ထုပ်Tools needed:
Skep Girth Gauge6
6
Sew the first coils to the crown
Sew the first coils to the crown
Coil the straw rope in a tight spiral around the crown. Push the awl through the coil below, pass split cane through, and pull each stitch snug about every 2 cm.
Materials for this step:
Split Cane1 မီတာTools needed:
Awl7
7
Spiral outward to start the dome
Spiral outward to start the dome
Continue spiralling outward from the crown, binding each new coil to the one below. The domed top of the hive begins to take shape.
Materials for this step:
Rye Straw1 ထုပ်Split Cane1 မီတာTools needed:
Awl8
8
Build the domed wall downward
Build the domed wall downward
Work the spiral down and out to build the wall, keeping the girth on the rope to hold thickness and every binding stitch tight and evenly spaced.
Materials for this step:
Rye Straw1 ထုပ်Split Cane1 မီတာTools needed:
AwlSkep Girth Gauge9
9
Keep the courses even
Keep the courses even
Control how far each coil steps outward so the dome stays smooth and symmetrical. Steady, even courses make a strong, weathertight hive.
Materials for this step:
Rye Straw1 ထုပ်Tools needed:
Awl10
10
Widen to the finished base
Widen to the finished base
As you near the bottom, let the coils reach the finished diameter of about 35–40 cm — the standard size for a colony of bees.
Materials for this step:
Rye Straw1 ထုပ်Split Cane1 မီတာTools needed:
Awl11
11
Cut the flight entrance
Cut the flight entrance
At the lower edge, cut a small entrance notch in a coil so the bees can come and go once the skep is set open-side down.
Tools needed:
Knife12
12
Finish and lock the base coil
Finish and lock the base coil
Complete the last coil at the base, taper off the straw rope, and lock the final binding stitches so the skep cannot unravel.
Materials for this step:
Split Cane1 မီတာTools needed:
Awl13
13
Trim the skep clean
Trim the skep clean
Trim protruding straw ends and stray cane with the knife to leave a clean rim and an even outer surface.
Tools needed:
Knife14
14
Clom the outside for weatherproofing
Clom the outside for weatherproofing
Smear a thin coat of cow-dung-and-clay daub over the straw to shed rain and seal drafts, then let it dry — the traditional 'clomming'.
Materials for this step:
Cow Dung2 ကီလို
Ball Clay1 ကီလို15
15
Cure the finished skep
Cure the finished skep
Cure the skep in a dry, airy place. Once fully dry it is ready to hive a swarm — set open-side down on a board or stand.
ပစ္စည်းများ
6- 1 ထုပ်Placeholder
- 6 မီတာPlaceholder
Connected Blueprint Materials
ဆက်စပ် အစီအစဉ်များ
ဤအစီအစဉ်များသည် အသိပညာမျှဝေသည် — နည်းပညာ၊ ပစ္စည်း သို့မဟုတ် မူများ
CC0 အများပိုင်
ဤအစီအစဉ်ကို CC0 အောက်တွင် ထုတ်ဝေထားသည်။ ခွင့်ပြုချက်မလိုဘဲ ကူးယူ၊ ပြင်ဆင်၊ ဖြန့်ဝေ နှင့် အသုံးပြုနိုင်သည်။
အစီအစဉ်မှတစ်ဆင့် ကုန်ပစ္စည်းများဝယ်ယူ၍ ဖန်တီးသူကို ပံ့ပိုးပါ ဖန်တီးသူ ကော်မရှင် ရောင်းချသူက သတ်မှတ်သည်၊ သို့မဟုတ် ဤအစီအစဉ်၏ ဗားရှင်းအသစ်ဖန်တီး၍ ဝင်ငွေခွဲဝေရန် သင့်အစီအစဉ်တွင် ချိတ်ဆက်မှုအဖြစ် ထည့်သွင်းပါ။