အနုပညာ
အလှအပနှင့် ကျန်းမာရေး
လက်မှုအနုပညာ
ယဉ်ကျေးမှုနှင့် သမိုင်း
ဖျော်ဖြေရေး
ပတ်ဝန်းကျင်
အစားအစာနှင့် အချိုရည်
ပြောင်းပြန်အင်ဂျင်နီယာပညာ
သိပ္ပံပညာများ
အားကစား
နည်းပညာ
ဝတ်ဆင်နိုင်သောပစ္စည်းများ
Two-Tine Pitchfork Split from One Iron Bar
Forge

ဖန်တီးသူ

Forge

14. အောက်တိုဘာ 2026NO
၉
၀
၀
၀
၀

Two-Tine Pitchfork Split from One Iron Bar

A pitchfork pitches hay, straw, manure or leaves: a long wooden shaft and slightly curved metal tines, wide apart for hay. Split one end of a wrought-iron bar, draw the halves into two round tines, draw a tang at the other end and fit it into the shaft under an iron ferrule. The picture: our diagram of the four stages.
အလယ်အလတ်
A day

ညွှန်ကြားချက်များ

1

Draw the tang

Heat one end of the bar and draw a square tapered tang about 10 cm long.

ဤအဆင့်အတွက် ကုန်ကြမ်းများ:

ထုလုပ်သံတုံးထုလုပ်သံတုံး1 ခု

လိုအပ်သော ကိရိယာများ:

ပန်းပဲမီးဖိုပန်းပဲမီးဖို
ပန်းပဲခုံပန်းပဲခုံ
ကန့်လန့်ဖြတ် ချွန်ခေါင်းတူကန့်လန့်ဖြတ် ချွန်ခေါင်းတူ
ပန်းပဲညှပ်ပန်းပဲညှပ်
ဂဟေဆော်လက်အိတ်ဂဟေဆော်လက်အိတ်
2

Split the bar

At a good heat, split the other end down the middle over the hot cut, about 12 cm deep, working from both faces.

လိုအပ်သော ကိရိယာများ:

ပန်းပဲမီးဖိုပန်းပဲမီးဖို
ပန်းပဲခုံဖြတ်ဆောက်ပန်းပဲခုံဖြတ်ဆောက်
ကန့်လန့်ဖြတ် ချွန်ခေါင်းတူကန့်လန့်ဖြတ် ချွန်ခေါင်းတူ
ပန်းပဲညှပ်ပန်းပဲညှပ်
ဂဟေဆော်လက်အိတ်ဂဟေဆော်လက်အိတ်
3

Draw the tines

Open the two halves into a V, then draw each one out round and to a point. Bend them parallel, about 15 cm apart, and give them a slight curve.

လိုအပ်သော ကိရိယာများ:

ပန်းပဲမီးဖိုပန်းပဲမီးဖို
ပန်းပဲခုံပန်းပဲခုံ
ကန့်လန့်ဖြတ် ချွန်ခေါင်းတူကန့်လန့်ဖြတ် ချွန်ခေါင်းတူ
ပန်းပဲညှပ်ပန်းပဲညှပ်
ဂဟေဆော်လက်အိတ်ဂဟေဆော်လက်အိတ်
4

Ferrule

Cut a strip of sheet iron, roll it hot into a ring that fits tightly over the end of the shaft, and drive it on.

ဤအဆင့်အတွက် ကုန်ကြမ်းများ:

သံပြား (တူဖြင့်ထုထားသော)သံပြား (တူဖြင့်ထုထားသော)1 ခု

လိုအပ်သော ကိရိယာများ:

သံပြားညှပ်ကတ်ကြေးသံပြားညှပ်ကတ်ကြေး
ပန်းပဲမီးဖိုပန်းပဲမီးဖို
ပန်းပဲခုံပန်းပဲခုံ
ကန့်လန့်ဖြတ် ချွန်ခေါင်းတူကန့်လန့်ဖြတ် ချွန်ခေါင်းတူ
ပန်းပဲညှပ်ပန်းပဲညှပ်
ဂဟေဆော်လက်အိတ်ဂဟေဆော်လက်အိတ်
5

Fit the shaft

Drill the shaft end for the tang, drive the tang in, and pin it through the ferrule with a nail. File the tine points clean.

ဤအဆင့်အတွက် ကုန်ကြမ်းများ:

ဖြောင့်သောသစ်သားတံဖြောင့်သောသစ်သားတံ1 ခု
သံသံချွန်များသံသံချွန်များ1 ခု

လိုအပ်သော ကိရိယာများ:

လက်တူးစက်လက်တူးစက်
ကန့်လန့်ဖြတ် ချွန်ခေါင်းတူကန့်လန့်ဖြတ် ချွန်ခေါင်းတူ
သတ္တုရိုက်တံသတ္တုရိုက်တံ
6

Tine length

Jupyter မှတ်စုစာအုပ် ဖွင့်နေသည်…

ပစ္စည်းများ

4

လိုအပ်သော ကိရိယာများ

9

ဤဘလူးပရင့်က ပြုလုပ်သည်

ဆက်စပ် အစီအစဉ်များ

ဤအစီအစဉ်များသည် အသိပညာမျှဝေသည် — နည်းပညာ၊ ပစ္စည်း သို့မဟုတ် မူများ

CC0 အများပိုင်

ဤအစီအစဉ်ကို CC0 အောက်တွင် ထုတ်ဝေထားသည်။ ခွင့်ပြုချက်မလိုဘဲ ကူးယူ၊ ပြင်ဆင်၊ ဖြန့်ဝေ နှင့် အသုံးပြုနိုင်သည်။

အစီအစဉ်မှတစ်ဆင့် ကုန်ပစ္စည်းများဝယ်ယူ၍ လက်မှုပညာရှင်ကို ပံ့ပိုးပါ လက်မှုပညာရှင် ကော်မရှင် ရောင်းချသူက သတ်မှတ်သည်၊ သို့မဟုတ် ဤအစီအစဉ်၏ ဗားရှင်းအသစ်ဖန်တီး၍ ဝင်ငွေခွဲဝေရန် သင့်အစီအစဉ်တွင် ချိတ်ဆက်မှုအဖြစ် ထည့်သွင်းပါ။

ဆွေးနွေးချက်

(0)

ဝင်ရောက် ဆွေးနွေးချက်တွင် ပါဝင်ရန်

မှတ်ချက်များ ရယူနေသည်...