ပူးပေါင်းဆောင်ရွက်ခြင်း
အနုပညာ
အလှအပနှင့် ကျန်းမာရေး
လက်မှုအနုပညာ
ယဉ်ကျေးမှုနှင့် သမိုင်း
ဖျော်ဖြေရေး
ပတ်ဝန်းကျင်
အစားအစာနှင့် အချိုရည်
ပြောင်းပြန်အင်ဂျင်နီယာပညာ
သိပ္ပံပညာများ
အားကစား
နည်းပညာ
ဝတ်ဆင်နိုင်သောပစ္စည်းများ
Oblique Box-Dasher Churn: A Hollow Slanted Dasher, Open on Two Sides, Churns Fast and Gathers the Butter Inside It Turned Slow
Buttercup

ဖန်တီးသူ

Buttercup

11. နိုဝင်ဘာ 2026IE
၀
၀
၀
၀
၀

Oblique Box-Dasher Churn: A Hollow Slanted Dasher, Open on Two Sides, Churns Fast and Gathers the Butter Inside It Turned Slow

Moses D. Wells of Morgantown, Virginia, received US 31,756, dated 19 March 1861, for a churn dasher shaped as a slanted open box: two flat end plates carrying the journals, two curved face pieces with lips at opposite corners, and two open sides. It turns on a horizontal axis in a box whose bottom is curved to its sweep. Turned fast it churns; turned the same way slowly, it gathers the butter inside itself, the lips keeping it from being thrown out, so it lifts out in a lump. The patent gives no sizes; every size here is ours.
အလယ်အလတ်
About 2 days

ညွှန်ကြားချက်များ

1

Churning fast, gathering slow

Jupyter မှတ်စုစာအုပ် ဖွင့်နေသည်…
2

A round-bottomed box with a turning dasher, eight months before

Park's box works the butter with pins. Wells's hollow dasher gathers it inside itself.
3

Read US 31,756

"The dasher being hollow, a few slow turns of the same causes the butter to collect within the box so as to be removed in a lump. ... The object of the diagonal lips b', b', is, to gather the butter against, and prevent it from being thrown out of the box in turning it around."
4

Body B with a curved bottom, legs and lid

Glue up two hardwood ends 22 mm thick, 350 mm wide and 320 tall. On each draw the inside: a 300 mm half circle with its centre 160 mm up, and straight sides rising 150 mm above the centre to the top. Rout a groove 1.6 mm wide and 8 deep on that line. Cut a slot 16.6 mm wide down from the top edge to the centre, rounded at its foot, as the journal bearing, and a hardwood keeper that fills the slot above the journal. Bend a 1.5 mm stainless sheet 416 mm long into a U to fit the line, set it in both grooves with silicone sealant, and screw hardwood sides 22 mm thick outside its straight parts. Screw four hardwood legs 40 x 40 mm, 390 long, to the ends, splayed out. Cut a hardwood lid 444 x 350 x 22 mm, notched over the keepers, with a 25 mm air opening o.

ဤအဆင့်အတွက် ကုန်ကြမ်းများ:

သစ်မာပျဉ်ပြားသစ်မာပျဉ်ပြား4 ခု
သံမဏိချောပြားသံမဏိချောပြား1 ခု
ဆီလီကွန် ပိတ်ဆေးဆီလီကွန် ပိတ်ဆေး1 ခု
သစ်သားကော်သစ်သားကော်1 ခု
သစ်သားဝက်အူများသစ်သားဝက်အူများ30 ခု

လိုအပ်သော ကိရိယာများ:

စားပွဲလွှစားပွဲလွှ
သံလိုက်အိမ်မြှောင်သံလိုက်အိမ်မြှောင်
ဂျစ်ဆောဂျစ်ဆော
သစ်သားထွင်းစက်သစ်သားထွင်းစက်
သစ်သားဆောက်အစုံသစ်သားဆောက်အစုံ
ရော်ဘာတူရော်ဘာတူ
ကြိုးမဲ့ တူးစက်ကြိုးမဲ့ တူးစက်
တူးစက်ခေါင်းအစုံတူးစက်ခေါင်းအစုံ
ပေါက်ပြားပုံ ဓားသွားအစုံပေါက်ပြားပုံ ဓားသွားအစုံ
တံညှပ်တံညှပ်
ဝက်အူလှည့်အစုံဝက်အူလှည့်အစုံ
တိုင်းတာရေးတိပ်တိုင်းတာရေးတိပ်
5

Print the end plates a (two)

An end plate of the dasher: 15 mm thick, the slanted outline of Fig. 1 with curved top and bottom edges, a 50 mm boss at the centre. Print two; drill each 16 mm at the centre for a journal. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ဒီဇိုင်း ဖိုင်STLCC0 - Free
6

Dasher D: end plates a, face pieces b with lips b', journals

Cut two strips of 1.5 mm stainless sheet 360 mm long, each 160 mm wide; bend each to a curve of about 300 mm radius following the end plates' curved edges, with a 20 mm lip b' at one long edge turned on round the corner. Screw them to the end plates' curved edges, the lips at diagonally opposite corners, leaving the two slanted sides open. Push a 16 mm stainless journal into each end plate's boss and pin it: one 40 mm long, the other 90 mm for the crank. Lay the journals in the slots and drop in the keepers. Pin a crank of mild steel flat bar, 120 mm throw, with a hardwood handle, on the long journal.

ဤအဆင့်အတွက် ကုန်ကြမ်းများ:

PETG ဖီလာမင့်PETG ဖီလာမင့်1 ခု
သံမဏိချောပြားသံမဏိချောပြား1 ခု
သစ်သားဝက်အူများသစ်သားဝက်အူများ16 ခု
သံမဏိချောတံသံမဏိချောတံ1 ခု
စပလစ်ပင်စပလစ်ပင်3 ခု
သံမဏိပျော့ ပြားချောင်းသံမဏိပျော့ ပြားချောင်း1 ခု
သစ်သားမာ ချွန်တံများသစ်သားမာ ချွန်တံများ1 ခု

လိုအပ်သော ကိရိယာများ:

ဖီလမင့်သုံး 3D ပုံနှိပ်စက် (FDM)ဖီလမင့်သုံး 3D ပုံနှိပ်စက် (FDM)
သံပြားညှပ်ကတ်ကြေးသံပြားညှပ်ကတ်ကြေး
ရော်ဘာတူရော်ဘာတူ
ကြိုးမဲ့ တူးစက်ကြိုးမဲ့ တူးစက်
တူးစက်ခေါင်းအစုံတူးစက်ခေါင်းအစုံ
သံဖြတ်လွှသံဖြတ်လွှ
တံစဉ်း (လက်တံစဉ်း)တံစဉ်း (လက်တံစဉ်း)
စားပွဲညှပ်စားပွဲညှပ်
ဝက်အူလှည့်အစုံဝက်အူလှည့်အစုံ
7

The build in 3D

FreeCAD model of this build, cut open: the round stainless bottom in grooved ends with slotted bearings and keepers, the legs and lid with its air opening, and the slanted hollow dasher with its curved, lipped face pieces and crank.
ဒီဇိုင်း ဖိုင်BLENDCC0 - Free
8

Churn and gather

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the box, so it stands below the axis, and put on the lid. Turn the crank briskly, timing it. When the butter comes, turn the same way slowly for a few turns until it gathers inside the dasher. Lift off the lid and keepers, lift the dasher out by its journals, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

ဤအဆင့်အတွက် ကုန်ကြမ်းများ:

ခရင်မ်အထူခရင်မ်အထူ10 l
ပင်လယ်ဆားကြမ်းပင်လယ်ဆားကြမ်း1 ခု
ရေရေ1 ခု

လိုအပ်သော ကိရိယာများ:

ထိုးထားသော တံစို့သာမိုမီတာထိုးထားသော တံစို့သာမိုမီတာ
အချိန်တိုင်းနာရီအချိန်တိုင်းနာရီ
ဒစ်ဂျစ်တယ် မီးဖိုချောင်ချိန်ခွင်ဒစ်ဂျစ်တယ် မီးဖိုချောင်ချိန်ခွင်
သံမဏိချော ရောစပ်ခွက်ကြီးသံမဏိချော ရောစပ်ခွက်ကြီး
9

Troubleshooting

Box-dasher churn troubleshooting.

Flow

Loading...
10

History and honest limits

**Moses D. Wells** of Morgantown, Monongalia County, Virginia (now West Virginia), US 31,756, 19 March 1861, "Churn-Dasher". He claimed "the oblique box dasher D constructed and operating substantially as set forth, that is to say, with two flat sides, two curved sides, and two open sides, and turned in the same direction for churning, and for gathering the butter, but at various velocities". He says only that the journals have "suitable connections to facilitate the removal of the dasher"; ours lie in open slots under keepers. The patent gives no sizes; every size here is ours.

ပစ္စည်းများ

13

လိုအပ်သော ကိရိယာများ

21

ဒီဇိုင်းဖိုင်များ

2

CC0 အများပိုင်

ဤအစီအစဉ်ကို CC0 အောက်တွင် ထုတ်ဝေထားသည်။ ခွင့်ပြုချက်မလိုဘဲ ကူးယူ၊ ပြင်ဆင်၊ ဖြန့်ဝေ နှင့် အသုံးပြုနိုင်သည်။

အစီအစဉ်မှတစ်ဆင့် ကုန်ပစ္စည်းများဝယ်ယူ၍ လက်မှုပညာရှင်ကို ပံ့ပိုးပါ လက်မှုပညာရှင် ကော်မရှင် ရောင်းချသူက သတ်မှတ်သည်၊ သို့မဟုတ် ဤအစီအစဉ်၏ ဗားရှင်းအသစ်ဖန်တီး၍ ဝင်ငွေခွဲဝေရန် သင့်အစီအစဉ်တွင် ချိတ်ဆက်မှုအဖြစ် ထည့်သွင်းပါ။

ဆွေးနွေးချက်

(0)

ဝင်ရောက် ဆွေးနွေးချက်တွင် ပါဝင်ရန်

မှတ်ချက်များ ရယူနေသည်...