Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ

Crosshead Dasher Churn: Dashers Hinged to a Rising Crosshead Slide Their Outer Ends Up Inclined Grooves, Counter-Dashers Above
Harry Abbott of North Huron, New York, received US 28,723, dated 19 June 1860, for a churn. In a long box a cross-head in the middle is raised and lowered by a lever; a frame dasher of rods is hinged to each side of it, its outer end sliding in a groove in the box's sides that slopes up inward, so the dashers' inner ends rise and fall while their outer ends move in and out. Above each, a dasher hinged to the box's end works against it and keeps the cream from splashing up.
The patent gives no sizes; every size here is ours.
Дээд шат
About 3 days
Зааварчилгаа
1
1
Inner ends up and down, outer ends in and out
Inner ends up and down, outer ends in and out
Jupyter дэвтэр ачаалж байна…
2
2
A hinged dasher in a long box, four months before
A hinged dasher in a long box, four months before
Cunningham swings one dasher from one end. Abbott lifts two from the middle and guides their outer ends in grooves.
3
3
Read US 28,723
Read US 28,723
"Arranged thus, the lower dashers E, E, have a compound motion; the inner ends being raised and lowered nearly vertically, while the outer ends are guided in and out nearly horizontally. The milk, or cream, passing through the rods g, g, of the dashers E, E, is violently and effectively agitated; while the rods o, o, of the auxiliary dashers, which have opposite and antagonistic motions, being arranged at right angles to the rods g, g, effectively break the currents, and allay the agitation on the surface."
4
4
Body A, legs a and grooves b and i
Body A, legs a and grooves b and i
From 20 mm hardwood board make a box 600 x 260 mm inside and 300 deep, glued and screwed, its inside joints sealed with silicone sealant, on four pine legs 480 mm long. Before assembling, rout in each side a vertical groove b 50 mm wide and 10 deep in the middle, and near each end an inclined groove i 14 mm wide and 10 deep, rising inward at 25 degrees from 45 mm above the floor and running into the groove b's path at its top, so the dashers lift out. Cut a lid with a 24 mm square hole in the middle.
Энэ алхмын материал:
Хатуу модон банз4 ширхэг
Нарсан модон материал2 ширхэг
Модны цавуу1 ширхэг
Модны шураг40 ширхэгШаардлагатай багаж:
Ширээний хөрөө
Гар фрезер
Транспортир
Утасгүй өрөм
Өрмийн үзүүрийн иж бүрдэл
Савааны хавчаар
Халив иж бүрдэл
Соронзон хэмжих туузан шугам5
5
Cross-head B and dashers E
Cross-head B and dashers E
Cut a hardwood cross-head 50 x 40 mm, 276 long, its ends fitting the grooves b. For each dasher make a frame of two hardwood side bars 16 x 50 mm, 240 long between pins, and ends f, with five 12 mm stainless rods g across it; fix a 10 mm stainless pin across its outer end, standing out 8 mm each side as the bearings h, and hinge its inner end to the cross-head with a 8 mm stainless pin and split pins, at d.
Энэ алхмын материал:
Хатуу модон банз1 ширхэг
Зэвэрдэггүй ган саваа4 ширхэг
Модны цавуу1 ширхэг
Шплинт4 ширхэгШаардлагатай багаж:
Ширээний хөрөө
Модны цүүцний багц
Утасгүй өрөм
Өрмийн үзүүрийн иж бүрдэл
Төмөр хөрөө
Дүрд (гар дүрд)6
6
Auxiliary dashers G
Auxiliary dashers G
Make each auxiliary dasher as a frame 230 mm long with four hardwood rods o, 8 mm thick, along its length, at right angles to the rods g below. Hinge its outer end to the box's end 200 mm up with a staple over a hook, held by a button. Let its middle rod run on past its inner end and through a screw eye on the dasher E's inner end, so G's inner end follows E's.
Энэ алхмын материал:
Хатуу модон банз1 ширхэг
Хатуу модон гадас1 ширхэг
Модны цавуу1 ширхэг
Цагирагт шураг2 ширхэг
Дэгээ ба гогцоо2 ширхэг
Модны шураг8 ширхэгШаардлагатай багаж:
Ширээний хөрөө
Утасгүй өрөм
Өрмийн үзүүрийн иж бүрдэл
Халив иж бүрдэл7
7
Rod C, lever D and fulcrum c
Rod C, lever D and fulcrum c
Cut a hardwood rod C 24 mm square, 420 long, and fix its foot in the cross-head's middle. Bolt a hardwood link c 90 mm between holes to a block on the outside of one end of the box, near the top. Cut a hardwood lever D, 720 mm long with a handle shaped at one end, and bolt it to the top of rod C and, 360 mm from that pin, to the link's top.
Энэ алхмын материал:
Хатуу модон банз2 ширхэг
Дугуй толгойт боолт3 ширхэг
Нейлон оруулгатай тогтоох гайка3 ширхэг
Модны цавуу1 ширхэг
Модны шураг4 ширхэгШаардлагатай багаж:
Ширээний хөрөө
Хөрөө (лобзик)
Утасгүй өрөм
Өрмийн үзүүрийн иж бүрдэл
Тохируулгатай түлхүүр8
8
The build in 3D
The build in 3D
FreeCAD model of this build, one side left off: the cross-head in its middle grooves, the two rod dashers hinged to it with their outer bearings in the inclined grooves, the auxiliary dashers above hinged at the ends, the rod C, the lever D and its swinging fulcrum link.
9
9
Churn
Churn
Pour about 15 litres of heavy cream at about 15 °C, checked with the thermometer, into the box and put on the lid. Work the lever up and down steadily, about 120 mm at the cross-head, timing it. When the butter comes, take off the lid, unhook the auxiliary dashers, lift the cross-head and dashers out by the grooves, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Энэ алхмын материал:
Өтгөн цөцгий15 l
Бүдүүн далайн давс1 ширхэг
Ус1 ширхэгШаардлагатай багаж:
Дотор нь үлдээдэг мэдрэгчтэй термометр
Секунд хэмжигч
Дижитал гал тогооны жин
Зэвэрдэггүй ган том хольц аяга10
10
Troubleshooting
Troubleshooting
Crosshead dasher churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Harry Abbott** of North Huron, Wayne County, New York, US 28,723, 19 June 1860 (signed 7 April 1860), "Churn". He claimed the dashers E guided by the vertical and inclined grooves, with the counter-acting dashers G. He gives no sizes and allows any equivalent way of working the cross-head; every size, the groove angle and the stroke here are ours.
Материал
15- 4 ширхэгТүр орлуулагч
- 2 ширхэгТүр орлуулагч
- 4 ширхэгТүр орлуулагч
- 52 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 4 ширхэгТүр орлуулагч
- 4 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 2 ширхэгТүр орлуулагч
- 2 ширхэгТүр орлуулагч
- 3 ширхэгТүр орлуулагч
- 3 ширхэгТүр орлуулагч
- 15 lТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
Шаардлагатай багаж
17- 1 vendor sell this, none ship to you yetТүр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- 1 vendor sell this, none ship to you yetТүр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- 1 vendor sell this, none ship to you yetТүр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- 1 vendor sell this, none ship to you yetТүр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
Загварын файлууд
1Энэ загвараар хийдэг
Холбоотой загварууд
Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

Toggle-Lever Churn: A Crank Crooks and Straightens a Jointed Lever, Rocking a Walking Beam Twice Each Turn
Buttercup зохиосон
Мод боловсруулалт
5
0
0
0
0
0

Spring-Pole Cam Churn: A Two-Arc Cam Lifts a Hinged Strip Dasher and a Wooden Spring Pole Drives It Down
Buttercup зохиосон
Мод боловсруулалт
4
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef зохиосон
ГАРААР ХИЙСЭН
63
0
0
0
0
0
CC0 Нийтийн домэйн
Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.
Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

