Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Air Blower: a Hand-Cranked Fan Blow-Bellows for a Portable Forge (Hasluck, 1904)
Forge

Зохиогч

Forge

4. Арван нэгдүгээр сар 2026NO
8
0
0
0
0

Air Blower: a Hand-Cranked Fan Blow-Bellows for a Portable Forge (Hasluck, 1904)

An air blower gives a fire a steady stream of air. Hasluck's Smiths' Work (1904) shows a small one for a home-made forge: a brass box with a four-winged tin fan on an iron spindle, spun fast by a hand wheel pressing on a rubber-covered roller. Unlike old bellows it blows continuously, through an outlet 2 1/2 in wide and 3/4 in deep. The book's drawings carry no sizes for the box, so its size, the sheet thickness and the metals of the wire and the plate are unknown here; the tools are ours. Source: P. N. Hasluck, Smiths' Work (1904), pp. 140-143, Figs. 202-211. Picture: their Figs. 203-204.
Дунд шат
Two days

Зааварчилгаа

1

Read Hasluck

"When this is all done, turn the handle rapidly; the fan inside will then revolve at a good rate, and a strong draught will be obtained."
2

Cut out the box

Cut the two sides and the bottom of the box from sheet brass, and a piece for the top covering, but do not join them yet. Hasluck gives no sizes for the box (unknown); its outlet is to be 2 1/2 in wide and 3/4 in deep.

Энэ алхмын материал:

Гуулин хуудасГуулин хуудас1 sides, bottom and covering

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
3

Make the fan

Make the iron spindle (Figs. 204, 205). Drill two holes in each of its four sides, one at each end, tap them, and screw in pieces of wire about 5/16 in long. Cut four pieces of tin, a little narrower than the box, and punch holes in them to match. Slip each wing over its wires, put a washer over each wire and rivet it over. Five or six wings may be used; then solder pieces of wire between them to stiffen them (Fig. 211).

Энэ алхмын материал:

Төмөр туйванТөмөр туйван1 spindle
Тодорхойгүй металлТодорхойгүй металл1 wire
Цагаан тугалган хуудасЦагаан тугалган хуудас1 four wings
Хавтгай угаагуурХавтгай угаагуур8 ширхэг

Шаардлагатай багаж:

Гар өрөмГар өрөм
Эрчлээ огтлох иж бүрдэлЭрчлээ огтлох иж бүрдэл
Төмөр хөрөөТөмөр хөрөө
Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Ривет алхРивет алх
Гагнуурын хэрэгсэлГагнуурын хэрэгсэл
4

Fit the spindle and close the box

Screw the brass bearings (Fig. 206), a ring with three spokes and a hole in the middle, to the two sides. Fit the iron spindle in the bearings, screw the sides and bottom together, then screw the covering over the top.

Энэ алхмын материал:

Гуулин хуудасГуулин хуудас1 two bearings
Машины шурагМашины шураг1 багц

Шаардлагатай багаж:

Гар өрөмГар өрөм
Эрчлээ огтлох иж бүрдэлЭрчлээ огтлох иж бүрдэл
5

Fit the hand wheel

The wheel has to be bought. Turn a brass spindle for it (Fig. 207), thread it at each end and fix it with a nut to a plate (Fig. 208); put on the wheel, hold it with a washer and another nut, and fit the knob on rather loosely. Before fixing the wheel, turn a small piece of wood (Fig. 209), put an india-rubber band over it and screw it onto the projecting end of the iron spindle. Fix the wheel so it presses tightly against this roller. Instead, both wheels may be grooved and driven by a band.

Энэ алхмын материал:

Төмөр гар дугуйТөмөр гар дугуй1 ширхэг
Гуулин баганзГуулин баганз1 wheel spindle
Тодорхойгүй металлТодорхойгүй металл1 plate
Зургаан талт эрэгЗургаан талт эрэг2 ширхэг
Хавтгай угаагуурХавтгай угаагуур1 ширхэг
Хөрөөдсөн банзХөрөөдсөн банз1 roller
Резинэн боолтРезинэн боолт1 ширхэг

Шаардлагатай багаж:

Металл эрэгМеталл эрэг
Эрчлээ огтлох иж бүрдэлЭрчлээ огтлох иж бүрдэл
Гар өрөмГар өрөм
6

Fit the nose-piece

Cut the nose-piece from sheet brass to the pattern (Fig. 210) and bend it at right angles along the dotted lines so it fits over the outlet end of the box. Rivet or solder its two edges together, drill it and screw it on. Turn the handle quickly to test the draught.

Энэ алхмын материал:

Гуулин хуудасГуулин хуудас1 nose-piece

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Гагнуурын хэрэгсэлГагнуурын хэрэгсэл
Гар өрөмГар өрөм
Хамгаалалтын нүдний шилХамгаалалтын нүдний шил
7

History and honest limits

Hasluck's "Home-made Portable Forges" chapter offers this fan as a cheaper, steadier alternative to the old leather bellows, costing about half as much. He adds that gun-metal is better than brass for all parts except the covering and nose-piece. The drawings carry no sizes, so the box size, the sheet thickness and the metals of the wing wires and wheel plate are unknown; the tools are ours.

Материал

11

Шаардлагатай багаж

9

Энэ загвараар хийдэг

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...