Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Arc Welder: AC Transformer with a Sliding Shunt Core (Fanger, US 2,248,070)
Forge

Зохиогч

Forge

9. Арван нэгдүгээр сар 2026NO
4
0
0
0
0

Arc Welder: AC Transformer with a Sliding Shunt Core (Fanger, US 2,248,070)

An AC arc welder is a step-down transformer whose current can be turned up and down. H. J. Fanger (US 2,248,070, 1941) cuts a gap through one leg of a laminated ring core and slides a laminated iron shunt bar through it: pushed in, it carries flux past the secondary and lowers the welding current; pulled out, the current rises. For arc welding he gives about 60 to 68 volts open circuit, 15 to 200 amps, dropping to 38 or 40 volts at the working arc, with a small coil on the shunt bar in series with the secondary. Source: H. J. Fanger, "Welding Transformer", US Patent 2,248,070 (filed 1938, granted 1941). Picture: its Figs. 1-5.
Дээд шат
Unknown

Зааварчилгаа

1

Read Fanger

"With arc welding, infinite control of the volume of the secondary current, between maximum and minimum is obtained by adjustment of the slidable shunt core without altering the welding characteristics of the current, also better ignition of the arc is had at a given voltage, and greater stability of the arc".
2

Stack the core

Build a single rectangular ring core of insulated iron laminations, held together with brass (or insulated) bolts or rivets in insulating tubes (Fig. 4). Cut a gap straight through one leg, accurately machined and finished, and make a circular joint through the opposite leg with the segments staggered to overlap in successive laminations. Core size, lamination iron and thickness are not given (ours: the tools).

Энэ алхмын материал:

Тодорхойгүй металлТодорхойгүй металл1 iron laminations
Зургаан талт болтны цуглуулгаЗургаан талт болтны цуглуулга1 brass bolts
Тодорхойгүй тусгаарлагч материалТодорхойгүй тусгаарлагч материал1 insulating tubes

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Суурин өрөмСуурин өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Дүрд (гар дүрд)Дүрд (гар дүрд)
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
3

Make the shunt bar

Make the sliding shunt section of the same laminated iron, a snug fit in the gap with its laminations edge-to-edge with the core's, and long enough to fill the gap at every position. Sheath both sides with a slightly wider plate of Bakelite that overlaps the edges of the gap to guide it. Fit a threaded rod on its outer end, working in a nut fixed to the section (or move it by hand, with calibration marks along one edge).

Энэ алхмын материал:

Тодорхойгүй металлТодорхойгүй металл1 shunt laminations
БакелитБакелит2 side plates
Зургаан талт болтны цуглуулгаЗургаан талт болтны цуглуулга1 brass bolts
Эрчилсэн савааЭрчилсэн саваа1 ширхэг
Зургаан талт эрэгЗургаан талт эрэг1 ширхэг

Шаардлагатай багаж:

Суурин өрөмСуурин өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Дүрд (гар дүрд)Дүрд (гар дүрд)
4

Wind the coils

Wind the primary and secondary windings on both legs of the core (Fig. 2), in series or in parallel to suit the line voltage and the current wanted. Wind a small auxiliary coil round the shunt bar's path, fixed so the bar slides through it, and connect it in series with the secondary through a reversing switch (some jobs weld better with the current through it one way). Turns and wire sizes are not given.

Энэ алхмын материал:

Зэс утасЗэс утас1 insulation and size not given

Шаардлагатай багаж:

Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
5

Spring the joints

On both sides of the gap and of the circular joint fit pairs of confronting angle plates, held by brass bolts in insulating sleeves and drawn together by spring bolts whose heads rest on slightly arched spring plates, so the joints close snugly on the sliding bar. A small lever on the gap-joint nut gives a half turn to release the bar for moving. The angle-plate material is not given.

Энэ алхмын материал:

Тодорхойгүй материалТодорхойгүй материал4 angle plates
Зургаан талт болтны цуглуулгаЗургаан талт болтны цуглуулга1 brass and spring bolts
Тодорхойгүй тусгаарлагч материалТодорхойгүй тусгаарлагч материал1 sleeves
Пүршний ган туузПүршний ган тууз1 arched spring plates
Зургаан талт эрэгЗургаан талт эрэг4 ширхэг

Шаардлагатай багаж:

Суурин өрөмСуурин өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Тохируулгатай түлхүүрТохируулгатай түлхүүр
6

Connect and set

Connect the primary to the line through a line switch, and the secondary leads to the electrode holder and the work. Pull the shunt bar out for more current, push it in for less: Fanger gives about 60-68 volts open circuit and 15-200 amps, dropping to 38-40 volts at the arc.

Энэ алхмын материал:

Асаах/унтраах унтраалгаАсаах/унтраах унтраалга1 line switch

Шаардлагатай багаж:

Тохируулгатай түлхүүрТохируулгатай түлхүүр

Материал

10

Шаардлагатай багаж

6

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...