Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Bench Power Supply: Regulated, with Adjustable Current Limit and a Pentode Pass Tube (Gately, Forbro, US 3,243,690, 1966)
Ed

Зохиогч

Ed

3. Арван нэгдүгээр сар 2026FI
11
0
0
0
0

Bench Power Supply: Regulated, with Adjustable Current Limit and a Pentode Pass Tube (Gately, Forbro, US 3,243,690, 1966)

An adjustable bench supply that holds its output voltage steady and lets you set the most current it will deliver, so a circuit under test cannot be damaged. A pentode tube in series with the output is the regulator; a bridge with Zener references and a five-transistor amplifier keeps the output equal to the setting of one knob. A meter switch reads volts, amps, and the current limit, which can be set without disturbing the voltage. Result: a regulated DC bench supply with adjustable current limiting. Source: J. R. Gately (Forbro Design), US 3,243,690 (1966). Unknown: all component values and the output rating. Picture: the patent drawing.
Дээд шат
Unknown

Зааварчилгаа

1

Wire the mains side

In a case, wire the power cord through a switch and a fuse to the primary of a transformer with four secondaries, and put a neon lamp across the primary to show the supply is on. One secondary (6.3 V) goes to two terminals for outside use, one heats the pentode, one is the main supply and one the bias supply. Ours: the case. Not given: the other winding voltages.

Энэ алхмын материал:

Хөнгөн цагаан бүрхүүлт хайрцагХөнгөн цагаан бүрхүүлт хайрцаг1 case
Залгууртай уян утасЗалгууртай уян утас1 ширхэг
Хөшүүрэгт унтраалгаХөшүүрэгт унтраалга1 ширхэг
Гал хамгаалагчГал хамгаалагч1 ширхэг
Буулгагч трансформаторБуулгагч трансформатор1 four secondaries
Неоны заагч дэнНеоны заагч дэн1 ширхэг
Холболтын шонХолболтын шон2 6.3 V terminals

Шаардлагатай багаж:

Гар өрөмГар өрөм
Халив иж бүрдэлХалив иж бүрдэл
2

Build the rectifiers

Rectify the centre-tapped main winding with two rectifiers and smooth it with a capacitor. From the bias winding make two more supplies: one through two rectifiers with by-pass capacitors to a smoothing capacitor, for the pentode's screen and the reference circuit; the other through one rectifier and a capacitor, for the pentode's grid bias. Not given: the values.

Энэ алхмын материал:

ДиодДиод5 rectifiers
Электролитийн конденсаторЭлектролитийн конденсатор3 smoothing
Конденсаторын багцКонденсаторын багц1 by-pass
Гагнуурын утасГагнуурын утас1 as needed

Шаардлагатай багаж:

Гагнуурын хэрэгсэлГагнуурын хэрэгсэл
3

Fit the pass tube and reference

Put the pentode in series with the positive output: plate to the main supply, cathode through two current-sensing resistors (one fixed, one adjustable) to the + output terminal; suppressor tied to the cathode, screen fed through a resistor. Build the reference: a Zener fed through a resistor feeds a second Zener at constant current, giving a fixed voltage. Against it set two resistors and the voltage-control variable resistor: the output voltage is proportional to that resistor's setting. Not given: the tube type and values.

Энэ алхмын материал:

Пентод лаазПентод лааз1 series pass tube
Зенер диодЗенер диод2 ширхэг
ЭсэргүүцэлЭсэргүүцэл1 багц
РеостатРеостат2 voltage control, current-limit range
Холболтын шонХолболтын шон2 output + and -
Гагнуурын утасГагнуурын утас1 as needed

Шаардлагатай багаж:

Гагнуурын хэрэгсэлГагнуурын хэрэгсэл
4

Build the error amplifier and current limit

Build a five-transistor amplifier that drives the pentode's grid to keep the bridge balanced: a PNP emitter follower, an NPN stage, a PNP emitter follower with a resistor-capacitor roll-off against oscillation, a PNP driver whose base resistor has a capacitor across it for quick response, and an NPN clamp whose base is set by a potentiometer. Feed the voltage across the current-sensing resistors to the driver's base through a diode: above the limit it takes over and turns the pentode down. Choose the fixed sensing resistor to limit at about 125 % of rated current, trim with the potentiometer, and use the adjustable one to set lower limits. Not given: the transistor types and values.

Энэ алхмын материал:

PNP транзисторPNP транзистор3 ширхэг
NPN транзисторNPN транзистор2 ширхэг
ДиодДиод1 ширхэг
ПотенциометрПотенциометр1 ширхэг
Конденсаторын багцКонденсаторын багц1 roll-off, speed-up
ЭсэргүүцэлЭсэргүүцэл1 багц
Гагнуурын утасГагнуурын утас1 as needed

Шаардлагатай багаж:

Гагнуурын хэрэгсэлГагнуурын хэрэгсэл
5

Fit the meter and use it

Fit a meter with a four-pole, three-position switch. Position 1 reads output volts through a multiplier resistor; position 2 reads current across a shunt in the negative line; position 3 (spring-return) puts a load resistor across the output and swaps a fixed resistor for the voltage control, so you can turn the limit control until the current limits at the value you want, without touching the voltage setting. Release the switch and use the supply.

Энэ алхмын материал:

Хөдлөх ороомогт самбарын хэмжүүрХөдлөх ороомогт самбарын хэмжүүр1 ширхэг
Эргэдэг унтраалгаЭргэдэг унтраалга1 4-pole, 3-position
ЭсэргүүцэлЭсэргүүцэл1 multiplier, shunt, load resistors
Тодорхойгүй материалТодорхойгүй материал1 terminal strip

Шаардлагатай багаж:

Гагнуурын хэрэгсэлГагнуурын хэрэгсэл
Халив иж бүрдэлХалив иж бүрдэл

Материал

21

Шаардлагатай багаж

3

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...