Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)
Woody

Зохиогч

Woody

13. Арван нэгдүгээр сар 2026NO
6
0
0
0
0

Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)

E. E. Hulgan's lathe from The Boy Mechanic, Book 2 (1915), "in which wood and light metal articles may be turned": a 5 ft bed of two 2 by 4 in hardwood rails, a headstock clamped by bolts with a 3/4 in steel spindle in brass bearings and a three-step pulley, a bolted hardwood tailstock with a screw-fed dead centre, a sliding tool rest, and a screw-on chuck. Driven from a countershaft or by foot.
Дээд шат
About 1-2 weeks

Зааварчилгаа

1

His sizes, and the pulley speeds

Jupyter дэвтэр ачаалж байна…
2

Read The Boy Mechanic, Book 2

"A strong, substantial lathe in which wood and light metal articles may be turned can be made by carefully following the description below and the detailed drawings of the parts."
3

Make the bed

Cut two pieces of straight-grained, smooth 2 by 4 in hardwood, 5 ft long, and hold them apart at each end with blocks of wood 2 in wide (Fig. 9 shows 2 in rails with a 2 in gap). The bed can be longer or shorter.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз2 ширхэг
Модны шурагМодны шураг1 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Гар цүүц (модны хусуур)Гар цүүц (модны хусуур)
Гар өрөмГар өрөм
Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
4

Build the headstock frame

Make the two hardwood end pieces to the shape of Figs. 1 and 2 (2 in thick, 2 in apart on an 8 in base, 7-1/2 in high, 6 in wide at the bottom) and screw them to the base. Nail a slider 1 in thick and 10 in long, just wide enough to slide between the bed rails, under the base, 2 in from its rear end. Bore two 1/2 in holes through base and slider and put two 1/2 in bolts through them and through another slide and board under the bed, so tightening the nuts clamps the headstock. Screw a half-round wedge-shaped brace inside the frame against the front end.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз1 ширхэг
Дугуй толгойт боолтДугуй толгойт боолт2 ширхэг
Зургаан талт эрэгЗургаан талт эрэг2 ширхэг
Модны шурагМодны шураг1 ширхэг
ХадаасХадаас1 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Модны цүүцнүүдМодны цүүцнүүд
Гар мушгиур өрөм ба үзүүрГар мушгиур өрөм ба үзүүр
Гар өрөмГар өрөм
5

Make the spindle and bearings

Make the spindle of tool steel or steel tubing, 3/4 in in diameter and 14 in long, and cut a thread on one end. Rivet on a hardened steel collar, 1/4 by 1-1/2 in, to turn against another collar of the same size on the headstock; screw a third collar to the rear end piece and fix a collar with a removable pin on the spindle, fitted to turn easily with no end play. Drill brass tubing for the spindle as bearings and wedge them into the headstock 6 in above the bed, in line; drill small oil holes from the top.

Энэ алхмын материал:

Багажийн ган савааБагажийн ган саваа1 ширхэг
Бүтээцийн ган хоолойБүтээцийн ган хоолой1 ширхэг
Shaft CollarShaft Collar4 ширхэг
Ган риветГан ривет1 ширхэг
Гуулин хоолойГуулин хоолой1 ширхэг

Шаардлагатай багаж:

Төмөр хөрөөТөмөр хөрөө
Эрчлээ огтлох иж бүрдэлЭрчлээ огтлох иж бүрдэл
Гар өрөмГар өрөм
Дүрд (гар дүрд)Дүрд (гар дүрд)
Ширээний хавчаарШирээний хавчаар
АлхАлх
6

Fit the stepped pulley

Make the pulleys 2 in wide, with the diameters on the drawing: 6, 4-1/2 and 3 in. Fasten them to the spindle with a removable pin. (Turned hardwood is our choice of material; he does not say.)

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз1 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Гар мушгиур өрөм ба үзүүрГар мушгиур өрөм ба үзүүр
Гар өрөмГар өрөм
7

Make the chuck and centres

For the chuck (Fig. 3), take shafting 1-1/2 in in diameter and 2-1/2 in long, drill a 1/2 in hole through its centre, ream and thread one end to fit the spindle, and fit a setscrew over the 1/2 in hole. Make a wood-turning centre, and other centres and drills, from 1/2 in tool steel.

Энэ алхмын материал:

Зөөлөн ган дугуй савааЗөөлөн ган дугуй саваа1 ширхэг
Багажийн ган савааБагажийн ган саваа1 ширхэг
Хонхор үзүүртэй тогтоох шурагХонхор үзүүртэй тогтоох шураг1 ширхэг

Шаардлагатай багаж:

Төмөр хөрөөТөмөр хөрөө
Гар өрөмГар өрөм
Нүх өргөсгөгчНүх өргөсгөгч
Эрчлээ огтлох иж бүрдэлЭрчлээ огтлох иж бүрдэл
Дүрд (гар дүрд)Дүрд (гар дүрд)
Ширээний хавчаарШирээний хавчаар
8

Build the tailstock

Build the tailstock (Figs. 4-6) of three pieces of hardwood 2 in thick and one 1 in thick, shaped as drawn, held together with four bolts 7-1/2 in long. Give it sliders and clamp it to the bed like the headstock, but with one bolt, and weld a handle to its nut for easy clamping. Drill a piece of tubing 2 in long for a 1/2 in dead centre and set it 1-1/2 in into the joint between the two upper pieces. Bore for a 1/2 in bolt to slide in the tube; chisel a recess behind the tube for a 1/2 in nut; turn a bolt 7 in long, threaded for 2 in, into nut and tube, and rivet a handle or wheel on its end. Make the centre of 1/2 in tool steel with a tapered point.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз2 ширхэг
Дугуй толгойт боолтДугуй толгойт боолт5 ширхэг
Зургаан талт эрэгЗургаан талт эрэг2 ширхэг
Бүтээцийн ган хоолойБүтээцийн ган хоолой1 ширхэг
Багажийн ган савааБагажийн ган саваа1 ширхэг
Ган риветГан ривет1 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Модны цүүцнүүдМодны цүүцнүүд
Гар мушгиур өрөм ба үзүүрГар мушгиур өрөм ба үзүүр
Гар өрөмГар өрөм
Нүүрсний зуухНүүрсний зуух
ДөшДөш
Дархны алхДархны алх
Дүрд (гар дүрд)Дүрд (гар дүрд)
9

Make the tool rest

The tool rest (Figs. 7-9) has a slide 3/4 by 3 by 13 in with a slot 1/2 by 6 in. Bolt the rest base on the slide so it can be adjusted, and screw the rest to the base. Raise or lower it with wedges between slide and base, and clamp it to the bed like the tailstock.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз1 ширхэг
Дугуй толгойт боолтДугуй толгойт боолт1 ширхэг
Зургаан талт эрэгЗургаан талт эрэг1 ширхэг
Модны шурагМодны шураг1 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Модны цүүцнүүдМодны цүүцнүүд
Гар мушгиур өрөм ба үзүүрГар мушгиур өрөм ба үзүүр
10

Troubleshooting

Wood lathe troubleshooting.

Flow

Loading...
11

History and honest limits

From "How to Make a Wood Lathe" by E. E. Hulgan, Marion, Ind., in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 434-436). Part shapes come from his Figs. 1-9; he gives no pulley material and no countershaft or foot-drive details. The pulley material, tools and metric figures are ours.

Материал

12

Шаардлагатай багаж

15

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...