Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ

Self-Righting Jumping Hurdle: Off-Centre Pivoted Swing Between Two Standards (Boy Mechanic, 1915)
C. C. Fraser's hurdle from The Boy Mechanic, Book 2 (1915): a 36 by 18 in swing hung on long nails slightly off centre between two standards joined by a reach. It turns at the slightest touch of the jumper's foot and rights itself again.
Анхан шат
About 2 hours
Зааварчилгаа
1
1
His cutting list in centimetres
His cutting list in centimetres
Jupyter дэвтэр ачаалж байна…
2
2
Read The Boy Mechanic, Book 2
Read The Boy Mechanic, Book 2
"The hurdle consists of two standards, a reach, and a swing."
3
3
Make the swing
Make the swing
Nail four pieces about 7/8 in thick and 1-1/2 in wide into a rectangle: two 36 in long and two 18 in long.
Энэ алхмын материал:
Нарсан банз1 ширхэг
Хадаас1 ширхэгШаардлагатай багаж:
Гар хөрөө
Алх
Соронзон хэмжих туузан шугам
Харандаа4
4
Make the standards and reach
Make the standards and reach
Make each standard of three pieces 7/8 in thick, 3 in wide and 18 in long, nailed firmly together as in his figure, and join their bases with a reach of the same stuff, 36 in long.
Энэ алхмын материал:
Нарсан банз1 ширхэг
Хадаас1 ширхэгШаардлагатай багаж:
Гар хөрөө
Алх
Соронзон хэмжих туузан шугам5
5
Hang the swing
Hang the swing
Bore a hole in each standard large enough for a long nail to turn freely but too small for its head to pass, and hang the swing on the nails at its ends, slightly off centre, so it swings at a touch and rights itself.
Энэ алхмын материал:
Хадаас1 ширхэгШаардлагатай багаж:
Гар өрөм
Алх6
6
Troubleshooting
Troubleshooting
Hurdle troubleshooting.
Flow
Loading...
7
7
History and honest limits
History and honest limits
From "How to Make a Hurdle" by C. C. Fraser, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 145). How far off centre the pivots go is not given. The tools and metric figures are ours.
Энэ загвараар хийдэг
Холбоотой загварууд
Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим
CC0 Нийтийн домэйн
Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.
Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

