Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)
Tinny

Зохиогч

Tinny

13. Арван нэгдүгээр сар 2026US
7
0
0
0
0

Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)

A canteen "for the camper or hiker", sent to The Boy Mechanic (1919) by J. R. Townsend of Itasca, Texas: two nickel-plated pie plates soldered rim to rim, the screw-capped neck of a metal-polish can soldered over an opening in the edge, and two wire loops for the snap hooks of a shoulder strap. The book gives no sizes: the plates set the size.
Анхан шат
About 2 hours

Зааварчилгаа

1

Read The Boy Mechanic

"Two good-quality pie plates were soldered at their edges to form a water-tight container." (J. R. Townsend, Itasca, Texas.)
2

Solder the plates together

Take two good-quality nickel-plated pie plates of the same size. Clean the rims, set them face to face, and solder them together all round the edge so the joint is water-tight. Use lead-free solder: this holds drinking water (our choice; the book only says solder).

Энэ алхмын материал:

Бялуу жигнэх тавагБялуу жигнэх таваг2 ширхэг
Тугалгагүй сантехникийн гагнуурТугалгагүй сантехникийн гагнуур1 ширхэг
ФлюсФлюс1 ширхэг

Шаардлагатай багаж:

Цахилгаан гагнуурын индүүЦахилгаан гагнуурын индүү
Металлын гилбэрМеталлын гилбэр
3

Cut the neck off the can

Take a small metal-polish can with a screw cap. As the book's drawing shows, cut off its sloping top with the threaded neck, and trim the cut edge.

Энэ алхмын материал:

Цагаан тугалган савЦагаан тугалган сав1 ширхэг

Шаардлагатай багаж:

Хүнд даацын металл хайчХүнд даацын металл хайч
Металлын гилбэрМеталлын гилбэр
4

Cut the opening and fit the neck

Cut an opening in the edge of the canteen to suit the neck. Fit the neck carefully over it and solder it all round.

Энэ алхмын материал:

Тугалгагүй сантехникийн гагнуурТугалгагүй сантехникийн гагнуур1 ширхэг
ФлюсФлюс1 ширхэг

Шаардлагатай багаж:

Гар өрөмГар өрөм
Металлын гилбэрМеталлын гилбэр
Цахилгаан гагнуурын индүүЦахилгаан гагнуурын индүү
5

Solder on the strap loops

Bend two short pieces of wire into loops and solder one at each side of the screw cap, as loops for the snap hooks of the shoulder strap.

Энэ алхмын материал:

Төмөр утасТөмөр утас1 ширхэг
Тугалгагүй сантехникийн гагнуурТугалгагүй сантехникийн гагнуур1 ширхэг
ФлюсФлюс1 ширхэг

Шаардлагатай багаж:

Хавтгай хошуут хямсааХавтгай хошуут хямсаа
Цахилгаан гагнуурын индүүЦахилгаан гагнуурын индүү
6

Fit the strap and test

Put a snap hook on each end of a shoulder strap and hook them into the loops. Fill the canteen with water, screw on the cap and check every joint for leaks (our test), then rinse it before use.

Энэ алхмын материал:

Арьсан оосорАрьсан оосор1 ширхэг
Пүрштэй дэгээПүрштэй дэгээ2 ширхэг

Шаардлагатай багаж:

Цэнгэг усЦэнгэг ус
7

Troubleshooting

Canteen troubleshooting.

Flow

Loading...
8

History and honest limits

From **The Boy Mechanic, Book 3**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1919 (Project Gutenberg 71856), "How to Make a Canteen", sent in by J. R. Townsend of Itasca, Texas. The book gives no sizes and names no tools; the lead-free solder, the tools, the strap material and the leak test are ours.

Материал

7

Шаардлагатай багаж

6

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...