Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Brake Cylinder: Piston with Packing Leather, Expander Ring and Release Spring (Westinghouse Air Brake Co., 1901)
Forge

Зохиогч

Forge

2. Арван нэгдүгээр сар 2026NO
15
0
0
0
0

Brake Cylinder: Piston with Packing Leather, Expander Ring and Release Spring (Westinghouse Air Brake Co., 1901)

The air cylinder that puts on a railway car's brakes. Air let into the pressure end drives the piston out, and its push rod works the brake levers. When the air is let out, a release spring pushes the piston back. A cup of leather, held against the wall by a spring ring, stops the air from leaking past the piston. Result: a brake cylinder. In the book's driver-brake example, an 8-inch cylinder fully applied puts 2,500 pounds on its piston. Source: Westinghouse Air Brake Company, Air Brake Instruction Book (1901), pp. 55-57 and 97. Unknown: every size except the 8-inch bore, and the metal of every part except the leather; the book does not give them. Picture: Wikimedia Commons.
Дээд шат
1 week

Зааварчилгаа

1

Bore the cylinder

Make the cylinder with a pressure end and an open end closed by the non-pressure head. Cut a small groove along the wall, the leakage groove: a slight flow of air into the cylinder then escapes through it to the open end instead of pushing the piston out. Unknown: the metal and the sizes (the book's example is an 8-inch cylinder). Ours: bored on a lathe.

Энэ алхмын материал:

Тодорхойгүй металлТодорхойгүй металл1 as required

Шаардлагатай багаж:

Металл эрэгМеталл эрэг
Нүх өргөсгөх бариулНүх өргөсгөх бариул
Токарийн багажны багц (HSS)Токарийн багажны багц (HSS)
Верньер штатахуун (штангенциркуль)Верньер штатахуун (штангенциркуль)
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
2

Make piston, follower and heads

Turn the piston with its sleeve, into which the push rod from the brake levers fits, a follower plate, and the non-pressure head. Drill the piston for the studs that hold the follower. Unknown: metal and sizes. Ours: lathe and drill press.

Энэ алхмын материал:

Тодорхойгүй металлТодорхойгүй металл1 as required

Шаардлагатай багаж:

Металл эрэгМеталл эрэг
Токарийн багажны багц (HSS)Токарийн багажны багц (HSS)
Суурин өрөмСуурин өрөм
Верньер штатахуун (штангенциркуль)Верньер штатахуун (штангенциркуль)
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
3

Fit the packing leather

Clamp the packing leather to the piston under the follower plate with studs and nuts; its flange presses against the cylinder wall to keep the air from escaping past the piston. Put the round spring packing expander inside the flange to hold it against the wall. Keep the follower nuts tight. Ours: the leather cut to shape with a knife.

Энэ алхмын материал:

Арьс ширАрьс шир1 as required
Тодорхойгүй металлТодорхойгүй металл1 studs and expander ring
Зургаан талт эрэгЗургаан талт эрэг1 багц

Шаардлагатай багаж:

Ажлын хутгаАжлын хутга
Тохируулгатай түлхүүрТохируулгатай түлхүүр
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
4

Assemble with the release spring

Slide the piston into the cylinder, put the release spring behind it and close the cylinder with the non-pressure head, so the spring forces the piston back to release whenever the air pressure is let out of the pressure end. The book's maintenance rule: a light grease in the cylinder, especially at the top and inside the packing leather where the expander rests.

Энэ алхмын материал:

Шахалтын пүршний иж бүрдэлШахалтын пүршний иж бүрдэл1 release spring

Шаардлагатай багаж:

Тохируулгатай түлхүүрТохируулгатай түлхүүр
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс

Материал

4

Шаардлагатай багаж

8

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...