Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Three-Series Beater Churn: Outer and Inner Loops Turn One Way, the Middle Loops and Centre Blades the Other
Buttercup

Зохиогч

Buttercup

11. Арван нэгдүгээр сар 2026IE
6
0
0
0
0

Three-Series Beater Churn: Outer and Inner Loops Turn One Way, the Middle Loops and Centre Blades the Other

Simon G. Cheever of Boston received US 28,560, dated 5 June 1860, for a machine for mixing paints, oils and powders that "may also be used as a butter mill or churn". Three nested series of loop beaters hang on one shaft: the outer and inner series turn one way and the middle series the other, while curved blades at the centre throw the cream outward into them. One crank drives it all through a wheel with a pinion on each side. This builds it as a churn. The patent gives no sizes; every size here is ours.
Дээд шат
About 2 days, plus printing

Зааварчилгаа

1

Three series, two directions

Jupyter дэвтэр ачаалж байна…
2

Nested dashers driven by one wheel and two pinions, seven weeks before

Dunham and Hipple nest two frames. Cheever nests three, the middle one turning against the other two.
3

Read US 28,560

"... the arrangement of the pinions on opposite sides of the driving wheel, and their connections through the collars with the outer and inner series of beaters or mixers, and the action of the central curved blades, is to throw the material constantly from the center to the circumference and there to submit it to the opposing forces of the beaters revolving in opposite directions."
4

Print the driving wheel C

Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Дизайны файлSTLCC0 - Free
5

Print the pinion D

Spur pinion, 16 teeth, module 2, with a hub; bored 12.4 mm for the shaft F. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Дизайны файлSTLCC0 - Free
6

Print the pinion E

Spur pinion, 16 teeth, module 2, with a hub; bored 18.4 mm for the sleeve of collar G. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Дизайны файлSTLCC0 - Free
7

Outer and inner series I, I on collars G and H2

Bend 6 mm stainless rod into two outer loops 220 mm across and 300 tall and two inner loops 120 across and 220 tall, open at the middle of top and bottom. Cut 130 mm of 18 mm stainless tube as the sleeve of collar G and fix two printed or hardwood hubs 32 mm across on it, 40 mm apart; screw the outer loops' top ends to the upper hub and the inner loops' to the lower, crossed at right angles. Screw their bottom ends to two hubs H2 bored 12.6 mm, which turn free on the shaft.

Энэ алхмын материал:

Зэвэрдэггүй ган савааЗэвэрдэггүй ган саваа4 ширхэг
Зэвэрдэггүй ган хоолойЗэвэрдэггүй ган хоолой1 ширхэг
Хатуу модон банзХатуу модон банз1 ширхэг
Машины шурагМашины шураг16 ширхэг
PETG филаментPETG филамент1 ширхэг

Шаардлагатай багаж:

FDM 3D хэвлэгчFDM 3D хэвлэгч
Ширээний хавчаарШирээний хавчаар
Төмөр хөрөөТөмөр хөрөө
Дүрд (гар дүрд)Дүрд (гар дүрд)
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Халив иж бүрдэлХалив иж бүрдэл
8

Middle series h, collars H and G2, blades L and M

Bend two middle loops 170 mm across and 260 tall. Screw their top ends to a ring H 44 mm across, bored 18.6 mm, that rides on the sleeve between G's two hubs, and their bottom ends to a hub G2 pinned to the shaft F between the two H2 hubs, set 45 degrees from the outer loops. Pin two curved printed blades, 180 tall and reaching 50 mm, on the shaft inside the inner loops.

Энэ алхмын материал:

Зэвэрдэггүй ган савааЗэвэрдэггүй ган саваа2 ширхэг
Машины шурагМашины шураг8 ширхэг
ШплинтШплинт3 ширхэг
PETG филаментPETG филамент1 ширхэг

Шаардлагатай багаж:

Ширээний хавчаарШирээний хавчаар
Төмөр хөрөөТөмөр хөрөө
Дүрд (гар дүрд)Дүрд (гар дүрд)
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Халив иж бүрдэлХалив иж бүрдэл
9

Shaft F, bridge, arm A, wheel C and crank K

Pass a 12 mm stainless shaft F, 500 mm long, up through G2, H2 and the sleeve. Cut a hardwood bridge 350 x 330 x 15 mm to lie on the bucket's rim, bored 24 mm in the middle for the sleeve. Fix the pinion E on the sleeve's top, and the pinion D on the shaft above it. Screw two hardwood arms to the bridge carrying a 12 mm stainless axle with the wheel C meshing E below and D above, and a crank K on its end; a hardwood bracket over D holds the shaft's top.

Энэ алхмын материал:

Зэвэрдэггүй ган савааЗэвэрдэггүй ган саваа2 ширхэг
Хатуу модон банзХатуу модон банз2 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг
Модны цавууМодны цавуу1 ширхэг
Модны шурагМодны шураг10 ширхэг
Shaft CollarShaft Collar4 ширхэг
PETG филаментPETG филамент1 ширхэг

Шаардлагатай багаж:

Ширээний хөрөөШирээний хөрөө
Хүрзэн өрмийн үзүүрийн багцХүрзэн өрмийн үзүүрийн багц
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Төмөр хөрөөТөмөр хөрөө
Савааны хавчаарСавааны хавчаар
Халив иж бүрдэлХалив иж бүрдэл
Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
10

The build in 3D

FreeCAD model of this build, the bucket cut open: the outer and inner loops on collar G and the H2 hubs, the middle loops on collar H and G2, the central blades, and on the bridge the wheel C with pinion E below and D above.
Дизайны файлBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, lower the beaters in and set the bridge on the rim. Turn the crank steadily, timing it. When the butter comes, lift the bridge and beaters out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Энэ алхмын материал:

Өтгөн цөцгийӨтгөн цөцгий8 l
Бүдүүн далайн давсБүдүүн далайн давс1 ширхэг
УсУс1 ширхэг

Шаардлагатай багаж:

Дотор нь үлдээдэг мэдрэгчтэй термометрДотор нь үлдээдэг мэдрэгчтэй термометр
Секунд хэмжигчСекунд хэмжигч
Дижитал гал тогооны жинДижитал гал тогооны жин
Зэвэрдэггүй ган том хольц аягаЗэвэрдэггүй ган том хольц аяга
12

Troubleshooting

Three-series beater churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Simon G. Cheever** of Boston, US 28,560, 5 June 1860, "Machine for Mixing Paints". He did not claim opposed pinions on one wheel, nor mixers or churn dashers turning oppositely, but the arrangement of the collars so the middle series turns against the outer and inner, with the central curved blades. His arm is metal and clamps into a dovetail socket on any bench; ours is hardwood on a bridge across the bucket. He leaves the number and shape of the beaters open; our loops, counts and every size are ours.

Материал

13

Шаардлагатай багаж

15

Загварын файлууд

4

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...