Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Colander: a Tinplate Colander with Perforated Body and Bottom (Hasluck, 1907)
Forge

Зохиогч

Forge

4. Арван нэгдүгээр сар 2026NO
9
0
0
2
0

Colander: a Tinplate Colander with Perforated Body and Bottom (Hasluck, 1907)

A tinsmith's colander for straining: a tapered tinplate body and a hollowed bottom, both punched full of holes, standing on a wired hoop, with two bow handles. The body pattern is a ring segment: outer radius = top diameter, inner radius = bottom diameter, which gives sides at 60 degrees. Source: Paul N. Hasluck, Tinplate Work (1907), pp. 50-51. Unknown: sizes, solder. Picture: Figs. 126-127 of the book.
Дунд шат
Unknown

Зааварчилгаа

1

Set out the body pattern

Choose the top and bottom diameters. On tinplate, strike an arc with radius equal to the top diameter and, from the same centre, one equal to the bottom diameter (Fig. 127); the sides then slope at 60 degrees. Mark the rows of holes, add edges for a grooved seam and the wire, and cut it out.

Энэ алхмын материал:

Цагаан тугалган хуудасЦагаан тугалган хуудас1 body

Шаардлагатай багаж:

Хоёр үзүүрт циркульХоёр үзүүрт циркуль
Зурмал зүүЗурмал зүү
Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
2

Break, punch and planish the body

'Break' the pattern through the rollers, turning it the opposite way each pass, so it won't crease when bent. Punch the holes on a hardwood block, then flatten and planish the burrs.

Шаардлагатай багаж:

Хуудас нугалах галзууХуудас нугалах галзуу
Хуудас төмрийн нүх цоологчХуудас төмрийн нүх цоологч
Хатуу модны блокХатуу модны блок
Тэгшлэх алхТэгшлэх алх
3

Seam and wire the body

Set off the edges for a grooved seam, bend the body to shape and seam it. Solder the seam inside. Set off an edge on the wide end and wire it with No. 10 B.W.G. wire. If you like, raise a swage about 1 1/2 in below the wired edge: it stiffens the colander and looks better.

Энэ алхмын материал:

Төмөр утасТөмөр утас1 No. 10 B.W.G.
Цагаан тугалга-хар тугалганы гагнуурЦагаан тугалга-хар тугалганы гагнуур1 seam

Шаардлагатай багаж:

Модон алхМодон алх
ГадасГадас
Цахилгаан гагнуурын индүүЦахилгаан гагнуурын индүү
ФлюсФлюс
4

Make and fit the bottom

Cut out the bottom, hollow it and edge it to fit the small end. Inside, mark circles from 1 in across at the centre, each 1 in wider than the last, out to the edge. Punch holes at short intervals round them and flatten the burrs on an upturned hollowing hammer. Solder the bottom on.

Энэ алхмын материал:

Цагаан тугалган хуудасЦагаан тугалган хуудас1 bottom
Цагаан тугалга-хар тугалганы гагнуурЦагаан тугалга-хар тугалганы гагнуур1 bottom

Шаардлагатай багаж:

Хоёр үзүүрт циркульХоёр үзүүрт циркуль
Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Хуудас төмрийн нүх цоологчХуудас төмрийн нүх цоологч
Тэгшлэх алхТэгшлэх алх
Цахилгаан гагнуурын индүүЦахилгаан гагнуурын индүү
ФлюсФлюс
5

Add the hoop and handles

Cut a strip 1 1/2 in wide, as long as the circumference of the bottom. Wire it with No. 10 B.W.G., round it, seam it and solder it on as the foot. Rivet a pair of bow handles opposite each other at the top.

Энэ алхмын материал:

Цагаан тугалган хуудасЦагаан тугалган хуудас1 hoop
Төмөр утасТөмөр утас1 hoop
Цагаан тугалга-хар тугалганы гагнуурЦагаан тугалга-хар тугалганы гагнуур1 hoop
БариулБариул2 bow handles
Төмөр риветТөмөр ривет1 number not given

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Цахилгаан гагнуурын индүүЦахилгаан гагнуурын индүү
ФлюсФлюс
Ривет алхРивет алх
6

Clean and scald

Clean with turpentine and whiting, then polish with dry whiting. Before first use, steep it a short time in boiling water, as for any metal article for the kitchen.

Шаардлагатай багаж:

СкипидарСкипидар
Кальцийн карбонат (цагаан шохой)Кальцийн карбонат (цагаан шохой)
УсУс

Материал

5

Шаардлагатай багаж

15

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...