Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Digital Oscilloscope: Waveform Stored in Memory and Shown on a CRT (Schumann, Nicolet, US 3,816,815, 1974)
Ed

Зохиогч

Ed

3. Арван нэгдүгээр сар 2026FI
10
0
0
0
0

Digital Oscilloscope: Waveform Stored in Memory and Shown on a CRT (Schumann, Nicolet, US 3,816,815, 1974)

An oscilloscope with a memory. After a trigger, an analog-to-digital converter measures the input at regular intervals and writes each reading into its own memory register, replacing the old one. The screen then shows the memory: each register's number sets the beam's height, its address sets the beam's place across. The last waveform can be held on the screen as long as you like. Result: a digital storage oscilloscope with 4,096 points of 12 bits, refresh and hold modes and single-shot capture. Source: R. W. Schumann (Nicolet), US 3,816,815 (1974). Unknown: sample rate, bandwidth, voltages and the parts used. Picture: the patent drawing.
Мэргэжилтэн
Unknown

Зааварчилгаа

1

Sample and convert the input

Bring the analog input to an analog-to-digital converter, through a BNC socket. A sampling oscillator, divided by four by two flip-flops so the first reading comes soon after the sweep starts, fires a one-shot multivibrator that gives the converter its measure command. The converter holds each 12-bit result on its output lines and signals the end of each conversion. Ours: a BNC socket. Not given: the sample rate.

Энэ алхмын материал:

Аналог-тоон хувиргагчАналог-тоон хувиргагч1 12-bit converter
Цагийн осцилляторЦагийн осциллятор1 sampling oscillator
Логик микросхемийн цуглуулгаЛогик микросхемийн цуглуулга1 flip-flops, one-shots, gates
Ижил тэнхлэгт холбогчийн хэрэгсэл (BNC / SO-239)Ижил тэнхлэгт холбогчийн хэрэгсэл (BNC / SO-239)1 input socket

Шаардлагатай багаж:

Гагнуурын хэрэгсэлГагнуурын хэрэгсэл
Утасны бүрээс хуулагчУтасны бүрээс хуулагч
2

Store each reading in memory

Wire an integrated-circuit memory of 4,096 registers, 12 bits each, that can be read without changing it. A 12-bit address counter picks the register. On each write command the register at the current address takes the last reading from the converter, and the counter steps on. When the sweep starts, a one-shot resets the counter to zero. When it reaches the last address, its last-address signal ends the sweep.

Энэ алхмын материал:

Интеграл хэлхээт санах ойИнтеграл хэлхээт санах ой1 4,096 x 12-bit store

Шаардлагатай багаж:

Гагнуурын хэрэгсэлГагнуурын хэрэгсэл
Утасны бүрээс хуулагчУтасны бүрээс хуулагч
3

Drive the CRT from the memory

Feed the addressed register's number to one digital-to-analog converter and the address to a second. Their outputs drive the vertical and horizontal deflection plates of a cathode-ray tube, so the beam always stands at the height of the stored reading and at the place of its address. Wire the sweep line to the tube's intensifier, to brighten the trace while a waveform is being taken.

Энэ алхмын материал:

Тоон-аналог хувиргагчТоон-аналог хувиргагч2 vertical and horizontal
Катодын цацрагт хоолойКатодын цацрагт хоолой1 display tube

Шаардлагатай багаж:

Гагнуурын хэрэгсэлГагнуурын хэрэгсэл
Утасны бүрээс хуулагчУтасны бүрээс хуулагч
4

Wire the trigger and the modes

A trigger input, usually from the leading edge of the input waveform, starts the sweep, once a measure flip-flop has armed it. Put a two-position mode switch on the face: MODE I and MODE II. Add a push button in the probe, a switch on the panel and an external initiate input; each goes through a flip-flop that removes contact bounce. Two more oscillators step the memory round to refresh the display between waveforms. Mount it all in a case with its supply. Ours: toggle switches, an aluminium case, a DC supply. Not given: the supply voltages.

Энэ алхмын материал:

Цагийн осцилляторЦагийн осциллятор2 display sequencing oscillators
Хөшүүрэгт унтраалгаХөшүүрэгт унтраалга2 mode and panel switches
ТовчлуурТовчлуур1 probe switch
Хөнгөн цагаан бүрхүүлт хайрцагХөнгөн цагаан бүрхүүлт хайрцаг1 case

Шаардлагатай багаж:

Шууд урсгалын тэжээлийн үүсгүүрШууд урсгалын тэжээлийн үүсгүүр
Суурин өрөмСуурин өрөм
Гагнуурын хэрэгсэлГагнуурын хэрэгсэл
5

Capture and hold a waveform

In MODE I, refresh: each new triggered waveform replaces the last on the screen. Press the probe or panel switch to hold: new waveforms are rejected and the last one stays on the screen. In MODE II the screen normally holds; on command, it takes the first waveform after the command, stores it and shows it steadily. Test it with a known signal.

Шаардлагатай багаж:

Функцын генераторФункцын генератор

Материал

10

Шаардлагатай багаж

5

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...