Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ

Brick Smith's Hearth: Stone Base, Firebrick Top in an Iron Rim, a Cannon-Shot Tuyere and a Slake Trough (Edwinson, 1886)
The fixed smith's hearth George Edwinson told Amateur Work readers to build (1886): stone below, firebrick in fireclay on top, every course bound with hoop iron, a 4 in. iron rim forming the hearth pan, a fire back and tuyere made from a 1 in. plate and a bored 14-pounder iron shot, a slanting flue, a 10 x 10 x 22 in. slake trough, and a clinker floor.
Дунд шат
Two to three days of building
Зааварчилгаа
1
1
His sizes
His sizes
Jupyter дэвтэр ачаалж байна…
2
2
Read Edwinson
Read Edwinson
"The foundation of this structure up to within one foot of the top may be of stone, but the finishing courses should be of firebrick."
3
3
Build the base
Build the base
Build the hearth in stone up to 1 ft (30 cm) below the top, binding every course with pieces of hoop iron. Leave an arch at the back for the coal pit and the blast pipe (figs. 4, 5). Overall size is ours: fit it to your shop.
Энэ алхмын материал:
Чулуун блок1 ширхэг
Төмөр хүрээ1 ширхэг
Галд тэсвэртэй шавар1 ширхэгШаардлагатай багаж:
Барилгын халбага (шпатель)
Ватерпас4
4
Make the fire back and tuyere
Make the fire back and tuyere
Bore a 3/4 in. hole through a 14-pounder iron shot and open it to a 1 in. taper on one side. Cut and countersink a hole in a 1 in. iron plate to take a third of the shot, and drill four 1/2 in. holes to bolt the plate through the wall with nuts and fish plates. (Or buy a fire back and tue-iron.)
Энэ алхмын материал:
Төмрийн бөөрөнхий (тэнцвэржүүлэх ачаа)1 ширхэг
Төмөр хавтан1 ширхэг
Зургаан талт болтны цуглуулга1 ширхэгШаардлагатай багаж:
Суурин өрөм
Дархны зуух
Алх5
5
Firebrick top and back
Firebrick top and back
Lay the top courses and the back wall round the tuyere in firebrick bedded and jointed with fireclay, still binding each course with hoop iron. Build in the fire back with the shot as the tuyere, and leave a slanting flue hole just above it (fig. 5).
Энэ алхмын материал:
Галд тэсвэртэй тоосго1 ширхэг
Галд тэсвэртэй шавар1 ширхэг
Төмөр хүрээ1 ширхэгШаардлагатай багаж:
Барилгын халбага (шпатель)
Ватерпас6
6
Fit the slake trough
Fit the slake trough
Before the last course, set in a water trough 10 in. deep and wide and 22 in. long, of sheet iron, cast iron or stone, inside the rim line; bolt a sheet-iron one to the rim. A sheet-iron division riveted across gives a coal trough too.
Энэ алхмын материал:
Зөөлөн ган хуудас1 ширхэг
Төмөр ривет1 ширхэг
Ус1 ширхэгШаардлагатай багаж:
Суурин өрөм
Алх7
7
Bind with the rim
Bind with the rim
Bind the top course with a rim of 1/4 x 4 in. iron, half below the brick edge and half above it to make the hearth pan, its ends bolted to the back wall with 3/8 in. bolts built into the brickwork.
Энэ алхмын материал:
Төмөр хавтан1 ширхэг
Зургаан талт болтны цуглуулга1 ширхэгШаардлагатай багаж:
Дархны зуух
Дөш
Алх
Суурин өрөм8
8
Connect the blast
Connect the blast
Bring the pipe from a fan or bellows under the arch to the back of the tue-iron. He reckons about 150 cu ft (4.2 m3) of air a minute for a welding heat: a 9 in. fan at about 360 rpm or a double-action bellows.
Шаардлагатай багаж:
Агаар үлээгч9
9
Lay the floor
Lay the floor
Ram wetted smiths', foundry or boiler clinkers sprinkled with a little Portland cement hard and level, with a thin layer of smithy cinder ashes beaten on top. Stone or ordinary concrete floors misbehave when hot iron is dropped on them.
Энэ алхмын материал:
Портланд цемент1 ширхэг
Ус1 ширхэгШаардлагатай багаж:
Алх10
10
Troubleshooting
Troubleshooting
Hearth troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
From George Edwinson, "Smithing and Forging" I, **Amateur Work, Illustrated**, vol. V (1886), pp. 161-162 and figs. 2, 4, 5 (checked on the archive.org scan amateurworkillus05lond). He gives no overall hearth size; that and the metric figures and tools are ours.
Материал
11- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 2 ширхэгТүр орлуулагч
- Түр орлуулагч
- 2 ширхэгТүр орлуулагч
- 2 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 2 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
Энэ загвараар хийдэг
Холбоотой загварууд
Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим
CC0 Нийтийн домэйн
Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.
Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

