Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ

Fuller, Pritchel and Hot Setts: Steel Welded into a Split Iron Bar, with Twisted Rod or Withy Handles (Edwinson, 1886)
The smith's own top and bottom tools, from George Edwinson's farrier's chapter in Amateur Work (1886): an inch iron bar upset, split into a fork and a steel wedge welded in, then forged into a fuller, pritchel punch, curved or straight hot sett, or a square-tanged bottom sett; the pritchel itself from 1/2 in. square tool steel; handles of twisted iron rod or green withy.
Дээд шат
A day at the forge for the set
Зааварчилгаа
1
1
His proportions
His proportions
Jupyter дэвтэр ачаалж байна…
2
2
Read Edwinson
Read Edwinson
"To make this tool, heat and upset the end of an inch bar of iron; then heat again and split with a sett."
3
3
Split the iron
Split the iron
Heat and upset the end of a 1 in. (25 mm) iron bar. Heat again and split it with a hot set into a fork 1 to 1 1/4 in. long by 3/4 in. wide (his fig. 108).
Энэ алхмын материал:
Давтсан төмөр гулдмай1 ширхэгШаардлагатай багаж:
Дархны зуух
Дөш
Том алх
Халуун цүүц
Дархны хавчаар4
4
Weld in the steel
Weld in the steel
Heat the end of a steel bar of similar size and forge a wedge to fit the fork (fig. 109). Bring both to a welding heat and weld them well together.
Энэ алхмын материал:
Тигелийн ган1 ширхэг
Борын нунтаг1 ширхэгШаардлагатай багаж:
Дархны зуух
Дөш
Том алх
Дархны хавчаар5
5
Forge the fuller
Forge the fuller
Cut off 2 in. of steel and 3 in. of iron for the tool. Forge the steel, with the iron behind it, into the fuller's rounded blade (fig. 102). Make the neck while it is still on the bar, then cut it off leaving a piece of iron for the head.
Шаардлагатай багаж:
Дархны зуух
Дөш
Алх
Халуун цүүц6
6
Same blank, other tools
Same blank, other tools
Pritchel punch: about 2 in. of iron and 1 in. of steel, shaped as fig. 103. Curved set: as the fuller but with a gouge-shaped blade (fig. 105). Top hot set: the same, with a chisel or wedge blade (fig. 106). Bottom set: a wedge of steel and iron, edge up, on a square tang that fits the anvil's square hole (fig. 107).
Энэ алхмын материал:
Давтсан төмөр гулдмай1 ширхэг
Тигелийн ган1 ширхэг
Борын нунтаг1 ширхэгШаардлагатай багаж:
Дархны зуух
Дөш
Алх
Том алх
Дархны хавчаар7
7
Forge the pritchel
Forge the pritchel
Forge 1/2 in. (13 mm) square tool steel into the tapered pritchel (fig. 104), 6 in. (150 mm) long. It punches nail holes in hot iron, so it need not be hardened.
Энэ алхмын материал:
Багажийн ган саваа1 ширхэгШаардлагатай багаж:
Дархны зуух
Дөш
Алх
Дархны хавчаар8
8
Fit the handles
Fit the handles
Rod handle: twist 3/8 in. iron rod once round the neck and weld the two ends together (fig. 110). Withy handle: take a green or half-green hazel, willow, oak or withy rod about 3 ft long, twist the middle 8-9 in., wrap it once round the neck and bind the two ends with wire or a link (figs. 106, 111).
Энэ алхмын материал:
Зөөлөн ган дугуй саваа1 ширхэг
Бургасны мөчир (уян)1 ширхэг
Төмөр утас1 ширхэгШаардлагатай багаж:
Дархны зуух
Дөш
Алх
Дархны хавчаар9
9
Harden the cutting tools (ours)
Harden the cutting tools (ours)
He gives no temper for these. Ours: harden and temper the set edges as for other hot-cutting tools, and cool them often in use.
Шаардлагатай багаж:
Дархны зуух
Хатууруулах тэвш10
10
Troubleshooting
Troubleshooting
Top-tool troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
From George Edwinson, "Smithing and Forging" VII, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 14-16 and figs. 101-111 (checked on the archive.org scan amateurworkillus06lond). He calls the top hot cutter a "sett"; we map it to the Hot Chisel head and the bottom sett to the Hot Cut Hardy head. Temper, metric figures and tools are ours.
Материал
7- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
Энэ загвараар хийдэг
Холбоотой загварууд
Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

Forge Welding Iron — Joining Two Pieces into One
Forge зохиосон
Гагнуур
77
0
0
0
3
0

Upsetting: Making It Thicker by Making It Shorter
Forge зохиосон
Металл боловсруулах багаж
52
0
0
0
0
0

Steeled Picks: Common Pick, Pickaxe and Miner's Pick, Iron Eye with Steel Points Welded In (Edwinson, 1886)
Forge зохиосон
Металл боловсруулалт
6
0
0
0
0
0
CC0 Нийтийн домэйн
Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.
Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.



