Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ

Electric Arc Furnace: the Héroult Series-Arc Steel Furnace (Stansfield, 1914)
Héroult's steel furnace: a tilting hearth like an open-hearth furnace, lined with dolomite, with two carbon electrodes coming down through the roof. The current goes down one electrode, arcs into the slag, passes through the molten steel and arcs back up the other, so the heat goes straight into the metal.
Result: an electric steel furnace about 7 x 4 ft inside for a 3 ton charge, run at about 350 kW and 110 V.
Source: A. Stansfield, The Electric Furnace, 2nd ed. (1914), pp. 115-116, 214-216. Unknown: case and tilting gear details, electrode size. Picture: a drawn diagram (Fig. 93 is blank in the scan).
Мэргэжилтэн
Unknown
Зааварчилгаа
1
1
Build the case and lining
Build the case and lining
Build the furnace in a steel case on a tilting mounting, about 7 x 4 ft inside, with charging doors at the ends. Line it with dolomite bricks and crushed dolomite; dolomite or magnesite on the hearth, which allows strongly basic slags. Ours: mild steel plate. Not given: the case and tilting gear, the bricks' making.
Энэ алхмын материал:
Зөөлөн ган хавтан1 case
Доломит (магнитай шохойн чулуу)1 lining and crushed dolomite
Магнезитын блокууд1 hearth, if magnesiteШаардлагатай багаж:
Нумын гагнуурын аппарат
Барилгын халбага (шпатель)
Тодорхойгүй хэмжээс2
2
Make the removable roof
Make the removable roof
Make the roof of silica brick, covered with steel plates and given eyes so it can be lifted off. Between the two electrode holes use bronze plates instead of steel, because steel there would raise the inductance of the AC circuit. Fit water jackets round each electrode hole for a close fit, so less heat escapes and the electrodes do not burn in the air. Ours: copper tube for the water jackets. Silica brick has no head here.
Энэ алхмын материал:
Тодорхойгүй материал1 silica brick
Зөөлөн ган хавтан1 roof plates
Хүрэл хавтан1 plates between electrodes
Зэс хоолой1 water jacketsШаардлагатай багаж:
Нумын гагнуурын аппарат
Суурин өрөм
Ус3
3
Hang the electrodes
Hang the electrodes
Use two vertical carbon electrodes, square in section. Carry each in a holder on an arm supported by the furnace itself, so its height does not change when the furnace tilts: four contact pieces round the electrode, drawn tight by a steel strap and a screw in the arm, with the cable bolted to them. Raise and lower each electrode separately, by a regulator controlled by the voltage between it and the metal. Not given: electrode size, the regulator's build.
Энэ алхмын материал:
Нүүрстөрөгчийн электрод2 electrodes
Тодорхойгүй металл1 holders, arms, contact piecesШаардлагатай багаж:
Суурин өрөм4
4
Melt and refine a charge
Melt and refine a charge
Charge steel scrap with some iron ore and lime. Keep each electrode a little above the slag, leaving room for its arc. Regulate the current by hand while the scrap melts, then switch to automatic; full power only after about an hour. Pour off the slag and make a second, then a third, with lime and a little sand and fluorspar, before the final additions. At La Praz this took about 350 kW at 110 V: 5 hours for 1.25 tons of low-carbon steel, 8 hours for 2.33 tons of high-carbon steel. Not given: the electric supply.
Шаардлагатай багаж:
УсМатериал
8- 1 roof platesТүр орлуулагч
- 1 lining and crushed dolomiteТүр орлуулагч
- 1 hearth, if magnesiteТүр орлуулагч
- 1 silica brickТүр орлуулагч
- 1 plates between electrodesТүр орлуулагч
- 1 water jacketsТүр орлуулагч
- 2 electrodesТүр орлуулагч
- 1 holders, arms, contact piecesТүр орлуулагч
Холбогдсон загварын материал

10% хамаарал
Mild Steel Plate and Sheet Hammered from a Billet
Forge зохиосон
Орчин үеийн
42
0
0
0
5
0

10% хамаарал
Hammering Bronze Sheet from a Cast Ingot — Raising and Planishing
Forge зохиосон
Металл боловсруулалт
57
0
0
0
1
0

10% хамаарал
Copper and Brass Tube Drawn from Strip
Forge зохиосон
Металл боловсруулалт
49
0
0
0
3
0
Энэ загвараар хийдэг
CC0 Нийтийн домэйн
Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.
Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.
