Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Electromagnet: Horseshoe Holding Magnet Sized by Its Pull (Underhill, 1903)
Volt

Зохиогч

Volt

3. Арван нэгдүгээр сар 2026SE
9
0
0
0
0

Electromagnet: Horseshoe Holding Magnet Sized by Its Pull (Underhill, 1903)

A holding electromagnet in its practical horseshoe form: two iron cores, each wound with wire, fastened to an iron yoke, and an iron armature across the poles. You size it from the pull you need: the pull sets the pole area, and the supply voltage sets the wire. Variable: the pull. Each pound needs a set area of pole, depending on the iron. Source: C. R. Underhill, The Electromagnet (1903), pp. 92, 106-118, 150. Unknown: sizes and the ampere-turns. Picture: Fig. 51 of the book.
Дунд шат
Unknown

Зааварчилгаа

1

Size the poles from the pull

Pull P (pounds) = B² × A / 72,134,000, where B is the flux density in lines per square inch and A the pole area in square inches. Working densities: wrought iron 90,000, cast steel 85,000, Mitis iron 80,000, ordinary cast iron 50,000, which give 112.3, 100.1, 88.72 and 34.66 lb per square inch of pole. Divide the pull you need by that figure to get the pole area. Underhill's example, for cast steel taken at 90,000: 10 lb needs 0.089 square inch, a core 0.336 inch across. A two-pole magnet holds twice the weight of a single pole at the same induction.

Шаардлагатай багаж:

Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
2

Make the cores, yoke and armature

Make the practical horseshoe magnet in three pieces besides the armature: two round cores and a yoke (back iron) to join them. Make an armature to lie across the two pole ends. Face the poles and the armature accurately; an uneven contact spreads the lines unevenly and weakens the pull. Ours: wrought iron. Not given: sizes, how the cores are fastened.

Энэ алхмын материал:

Давтсан төмөр гулдмайДавтсан төмөр гулдмай1 two cores, yoke, armature

Шаардлагатай багаж:

Металл эрэгМеталл эрэг
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
3

Choose the wire for the supply

Design the coil to stand the full supply voltage without overheating; never put a resistor in series with the magnet, as that wastes power and makes the magnet weaker. Pick the wire size that makes the coil's resistance equal to that of the line and the source, then try the next larger size, and keep the one giving more ampere-turns. A coil rises about 100 °F at about 0.9 watt per square inch of surface for a thin telephone-ringer coil, or 0.33 for a thick one (4 1/8 in across, 7 in long, 1 7/16 in thick), and the rise grows in proportion to the watts. Ours: the supply, e.g. 12 V.

Шаардлагатай багаж:

Шууд урсгалын тэжээлийн үүсгүүрШууд урсгалын тэжээлийн үүсгүүр
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
4

Wind the cores and fasten them to the yoke

Wind the wire directly onto each core between insulating end heads, and fasten the wound cores to the yoke. The joints between cores and yoke lose a little pull. Ours: enamelled copper wire. Not given: the winding method, the insulation.

Энэ алхмын материал:

Пааландсан зэс утасПааландсан зэс утас1 two coils
Тодорхойгүй тусгаарлагч материалТодорхойгүй тусгаарлагч материал1 end heads and core insulation
Тодорхойгүй металлТодорхойгүй металл1 core fastenings

Шаардлагатай багаж:

Үл мэдэгдэх ороох аргаҮл мэдэгдэх ороох арга
Металл эрэгМеталл эрэг
5

Switch on and hold

Connect the coils to the supply and put the armature against the faced poles: the magnet holds it with the pull it was sized for. When the armature touches the poles there is practically no leakage between them.

Шаардлагатай багаж:

Шууд урсгалын тэжээлийн үүсгүүрШууд урсгалын тэжээлийн үүсгүүр

Материал

4

Шаардлагатай багаж

4

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...