УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights
Penny

Зохиогч

Penny

14. Аравдугаар сар 2026DK
23
0
0
0
0

Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights

The oldest weighing machine is a beam with equal arms balanced on a pivot, a pan hanging from each end: put the load in one pan and known weights in the other until the beam lies level. Balances go back to the Fourth Dynasty of Egypt. A hardened knife edge makes it sensitive and a long pointer shows the smallest tilt; the weights are cast in brass and adjusted against each other. The picture: our diagram of the balance, its knife edge, pointer, pans and weights.
Дунд шат
Two to three days

Зааварчилгаа

1

Beam and knife edge

File a straight beam from flat tool steel with a hole exactly in the middle and one near each end, the two end holes equally far from the centre. Forge and file a short steel knife edge, harden and temper it, and fit it through the centre hole, edge down. File a long pointer onto the beam.

Энэ алхмын материал:

Хавтгай багажийн ган савааХавтгай багажийн ган саваа1 ширхэг

Шаардлагатай багаж:

Металлын гилбэрМеталлын гилбэр
Гар өрөмГар өрөм
Дижитал штангенциркуль 6 инчДижитал штангенциркуль 6 инч
Дархны зуухДархны зуух
Хатууруулах тэвшХатууруулах тэвш
Хамгаалалтын нүдний шилХамгаалалтын нүдний шил
2

Stand and bearing

Make an upright stand of hardwood with a hardened steel V-block on top, shallower than the knife edge, so the beam rocks freely. Mark a zero line behind the pointer.

Энэ алхмын материал:

Хатуу модны нарийн банзХатуу модны нарийн банз2 ширхэг
Зөөлөн ганан дугуй баганзЗөөлөн ганан дугуй баганз0.3 m

Шаардлагатай багаж:

Металлын гилбэрМеталлын гилбэр
Дархны зуухДархны зуух
Хатууруулах тэвшХатууруулах тэвш
3

Pans

Cut two equal brass discs, dish them slightly, drill three holes in each rim and hang each from an end hole on three equal cords.

Энэ алхмын материал:

Гуулин хуудасГуулин хуудас1 ширхэг
Лаадсан маалингын утасЛаадсан маалингын утас3 m

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Гар өрөмГар өрөм
Металлын гилбэрМеталлын гилбэр
4

Trim to level

With both pans empty, file the heavier side until the pointer rests on zero. Swap the pans and check again: if the pointer moves, the arms are unequal and the end holes need moving.

Шаардлагатай багаж:

Металлын гилбэрМеталлын гилбэр
5

Cast the weights

Melt brass and cast a row of plain cylinders a little heavy in green sand.

Энэ алхмын материал:

Гуулин ембүүГуулин ембүү2 кг
Модны нүүрсМодны нүүрс1 as required
Цутгамалын элсЦутгамалын элс5 кг

Шаардлагатай багаж:

Дархны зуухДархны зуух
Шавран тигель — галд тэсвэртэйШавран тигель — галд тэсвэртэй
Тигелийн хямсааТигелийн хямсаа
Цутгамлын хайрцаг (дээд ба доод)Цутгамлын хайрцаг (дээд ба доод)
Гагнуурын бээлийГагнуурын бээлий
6

Adjust the weights

Balance the largest weight against a litre of water measured in the cylinder (one kilogram, our reference), filing it down until the beam is level. Make the smaller ones by balancing pairs against a larger one and against each other, filing each to level.

Энэ алхмын материал:

УсУс1 литр

Шаардлагатай багаж:

Хуваарьтай цилиндрХуваарьтай цилиндр
Металлын гилбэрМеталлын гилбэр
7

A binary set of weights

Jupyter дэвтэр ачаалж байна…
8

Limits

The balance's form and use are as Wikipedia describes; the sizes and the water reference are ours. Water's density changes a little with temperature, so the reference is good to a few parts in a thousand.

Материал

9

Шаардлагатай багаж

12

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...