Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Sprung-Blade Inclined-Dasher Churn: The Blades Close to Pass the Narrow Top and Spread to Fill the Wide Bottom
Woody

Зохиогч

Woody

9. Арван нэгдүгээр сар 2026NO
9
0
0
0
0

Sprung-Blade Inclined-Dasher Churn: The Blades Close to Pass the Narrow Top and Spread to Fill the Wide Bottom

John U. Fiester of Winchester, Ohio, received US 22,945 in February 1859 for a churn with a slanting dasher in a tub wider at the bottom than the top, so it is hard to tip over. The dasher's two blades are held to the spindle by a yoke spring and guided by pins in the slots of a cross tie: they close to pass the narrow top and spread to fill the wide bottom. Holes let the cream through the blades, and square pockets cut part way in carry air down into it. This rung builds it in pine and hardwood with a crank.
Дунд шат
About 8 hours, plus printing

Зааварчилгаа

1

Tub, fill and the blades' reach

Jupyter дэвтэр ачаалж байна…
2

Holed beaters, before it

The Robies' beaters pass the cream through holes. Fiester's blades also have pockets that carry air down.
3

Read US 22,945

"... the yoke spring E and slots (a) allow the dasher blades to be forced easily into the smaller opening in the top of the tub, and when in to expand and fill the larger space at the bottom."
4

Print the journal box e

The block with the seat for the spindle's point. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Дизайны файлSTLCC0 - Free
5

Print the yoke collar

The collar on the spindle that holds the yoke spring. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Дизайны файлSTLCC0 - Free
6

Tub A and lid B

From 18 mm pine cut a floor 460 x 336 mm, two ends 400 mm wide at the foot, 320 mm at the top and 400 mm tall, and two sloping sides 336 mm wide that join them. Glue and screw the ends and sides on the floor so the tub is 400 mm wide inside at the floor and 320 mm at the top, 300 mm front to back. Cut a lid 374 x 336 mm with a turned dowel knob. Drill a 42 mm hole through the right side where the spindle meets it, about 345 mm above the inside floor.

Энэ алхмын материал:

Нарсан банзНарсан банз3 ширхэг
Модны цавууМодны цавуу1 ширхэг
Модны шурагМодны шураг40 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Хөрөө (лобзик)Хөрөө (лобзик)
Утасгүй өрөмУтасгүй өрөм
Нүх хөрөөдөгч багцНүх хөрөөдөгч багц
ХавчааруудХавчаарууд
Транспортир / өнцөг хэмжигчТранспортир / өнцөг хэмжигч
Элсэн цаасЭлсэн цаас
Халив иж бүрдэлХалив иж бүрдэл
Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
7

Spindle C and journal e

Cut a 40 mm hardwood dowel 641 mm long and whittle or plane one end to a point over 30 mm. Screw the journal box in the left corner of the floor, against the sloping side. Cut a half-lap notch 30 mm wide and 12 mm deep across the spindle 85 mm from its point for the cross tie.

Энэ алхмын материал:

PETG филаментPETG филамент1 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг
Модны шурагМодны шураг4 ширхэг

Шаардлагатай багаж:

FDM 3D хэвлэгчFDM 3D хэвлэгч
Гар хөрөөГар хөрөө
Модны цүүцнүүдМодны цүүцнүүд
Дүрд (гар дүрд)Дүрд (гар дүрд)
Халив иж бүрдэлХалив иж бүрдэл
8

Blades D, tie F and yoke E

Draw an oval 340 x 220 mm on 16 mm hardwood and cut it in two along its length, then take 4 mm off each straight edge so the halves clear the spindle. Drill four 20 mm holes f in each blade and chisel four 20 mm square pockets d, 8 mm deep with bevelled sides, facing the same way. Glue a 9 mm dowel pin b into each blade 31 mm from its straight edge, 30 mm from its lower end. Cut a hardwood cross tie F 190 x 30 x 16 mm with a 10 mm slot 30 mm long near each end, glue it into the spindle's notch, and drop the pins into its slots. Slide the collar onto the spindle above the blades and screw two spring steel strips 15 x 1.5 mm, 42 mm long, from the collar to each blade's top end.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз1 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг
Модны цавууМодны цавуу1 ширхэг
Пүршний ган туузПүршний ган тууз1 ширхэг
Машины шурагМашины шураг8 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка8 ширхэг

Шаардлагатай багаж:

Хөрөө (лобзик)Хөрөө (лобзик)
Утасгүй өрөмУтасгүй өрөм
Хүрзэн өрмийн үзүүрийн багцХүрзэн өрмийн үзүүрийн багц
Модны цүүцнүүдМодны цүүцнүүд
Төмөр хөрөөТөмөр хөрөө
Дүрд (гар дүрд)Дүрд (гар дүрд)
Элсэн цаасЭлсэн цаас
Халив иж бүрдэлХалив иж бүрдэл
9

Fit the dasher and crank

Pass the spindle's top out through the hole in the right side, squeeze the blades together through the tub's top and let them spread, and seat the point in the journal box. Fix a hardwood crank arm 130 mm long on the spindle outside the tub with a screw across, and glue in a 24 mm dowel handle 100 mm long.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз1 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг
Модны цавууМодны цавуу1 ширхэг
Модны шурагМодны шураг1 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Утасгүй өрөмУтасгүй өрөм
Хүрзэн өрмийн үзүүрийн багцХүрзэн өрмийн үзүүрийн багц
Халив иж бүрдэлХалив иж бүрдэл
10

The build in 3D

FreeCAD model of this build, the near half of the tub cut away: the sloping tub, the journal box, the slanting spindle with its two holed blades, the cross tie with its slots and pins, the yoke collar and springs, and the crank outside.
Дизайны файлBLENDCC0 - Free
11

Churn

Pour in about 12 litres of heavy cream at about 15 °C, checked with the thermometer, and put the lid on. Turn the crank steadily and time it: the blades dip in and out of the cream, the pockets carrying air down. When the butter comes, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Энэ алхмын материал:

Өтгөн цөцгийӨтгөн цөцгий12 l
Бүдүүн далайн давсБүдүүн далайн давс1 ширхэг
УсУс1 ширхэг

Шаардлагатай багаж:

Дотор нь үлдээдэг мэдрэгчтэй термометрДотор нь үлдээдэг мэдрэгчтэй термометр
Секунд хэмжигчСекунд хэмжигч
Дижитал гал тогооны жинДижитал гал тогооны жин
Зэвэрдэггүй ган том хольц аягаЗэвэрдэггүй ган том хольц аяга
12

Troubleshooting

Sprung-blade churn troubleshooting.

Flow

Loading...
13

History and honest limits

**John U. Fiester** of Winchester, Guernsey County, Ohio, US 22,945, "Churn": the drawing reads 15 February 1859, the text 25 February 1859. A tub wider at the top can be overset; his is wider at the bottom, and the sprung, guided blades still fill it. He claimed the adjustable dasher with its yoke spring, slotted cross tie and pins, holes and air pockets. He gave no sizes or materials: ours are a pine tub, hardwood dasher and steel springs.

Материал

12

Шаардлагатай багаж

18

Загварын файлууд

3

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...