Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Sliding-Head Churn Drive: The Churn Rides on the Pulley Head and Stays in Line When the Belt Is Slacked
Martin

Зохиогч

Martin

9. Арван нэгдүгээр сар 2026NO
8
0
0
0
0

Sliding-Head Churn Drive: The Churn Rides on the Pulley Head and Stays in Line When the Belt Is Slacked

Joseph Forsyth of Wheeling, Virginia, received US 22,022, dated 9 November 1858, for working a churn by power from a big belt wheel. The pulley head slides along a guide block to tighten or slack the belt, which starts or stops the churn. The churn stands on a carriage fixed to the head, so its shaft stays in line with the pulley's. A platform on four screws raises or lowers different churns to the pulley's height. This rung builds it full size with a hand-cranked wheel and a rope belt.
Дунд шат
About 2 days

Зааварчилгаа

1

Speed, rope and slack

Jupyter дэвтэр ачаалж байна…
2

Churns worked by power, before it

Brush worked a dasher from a dog's tread-wheel. Forsyth turns a crank churn by a belt and stops it by slacking the belt.
3

Read US 22,022

"The nature of my invention consists, first, in combining the carriage D with the movable pulley head H H in such a manner that the said carriage will move with the head when it is required to stop or start the motion of the churn, thereby enabling me to keep the shafts of the pulley, and churn in line."
4

Wheel A and posts B

Cut a plywood disc 1160 mm across and two discs 1200 mm across from 18 mm plywood. Glue and screw a larger disc to each face of the smaller one: the gap between them is the rope groove C. Screw a 160 mm hub block on each side. Stand two 70 mm posts 730 mm tall on 900 mm sills, 150 mm apart, each with two braces. Bolt a flange bearing on each post's outer face, 700 mm up, and run a 30 mm shaft M through bearings, posts and wheel, cross-bolted to the hub.

Энэ алхмын материал:

Фанер хуудасФанер хуудас3 ширхэг
Модны цавууМодны цавуу1 ширхэг
#8 × 1" модны шураг#8 × 1" модны шураг60 ширхэг
Зөөлөн мод 70x70 ммЗөөлөн мод 70x70 мм4 ширхэг
#10 x 3" модны шураг#10 x 3" модны шураг24 ширхэг
Фланцтай холхивчФланцтай холхивч2 ширхэг
Ганан гол 30 ммГанан гол 30 мм1 ширхэг
Зургаан талт болтны хэрэглэл M10Зургаан талт болтны хэрэглэл M105 ширхэг

Шаардлагатай багаж:

Хөрөө (лобзик)Хөрөө (лобзик)
Гар хөрөөГар хөрөө
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Хүрзэн өрмийн үзүүрийн багцХүрзэн өрмийн үзүүрийн багц
ХавчааруудХавчаарууд
Тохируулгатай түлхүүрТохируулгатай түлхүүр
ВатерпасВатерпас
Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
5

Crank

How the wheel is turned is not given; ours has a crank. Bolt a hardwood arm 350 x 70 x 30 mm on shaft M outside one bearing and glue a 30 mm dowel 150 mm long into it 280 mm from the shaft as the handle.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз1 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг
Модны цавууМодны цавуу1 ширхэг
Зургаан талт болтны хэрэглэл M10Зургаан талт болтны хэрэглэл M101 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Утасгүй өрөмУтасгүй өрөм
Хүрзэн өрмийн үзүүрийн багцХүрзэн өрмийн үзүүрийн багц
Элсэн цаасЭлсэн цаас
Тохируулгатай түлхүүрТохируулгатай түлхүүр
6

Guide block and pulley head

Screw a 900 mm guide block U of 70 mm timber to the floor in line with the wheel, 1300 mm from shaft M. Lay a 400 mm head block on it. Cut two frames H from 50 x 8 mm flat bar, 420 mm long, and bolt them to the head block's sides so their ends run down the guide block's sides. Bolt a flange bearing on each frame's outer face 400 mm up. Make the pulley O like the wheel: a 200 mm disc between two 240 mm rings. Fit it on a 30 mm shaft through the bearings.

Энэ алхмын материал:

Зөөлөн мод 70x70 ммЗөөлөн мод 70x70 мм2 ширхэг
#10 x 3" модны шураг#10 x 3" модны шураг8 ширхэг
Зөөлөн ганы хавтгай туйванЗөөлөн ганы хавтгай туйван2 ширхэг
Зургаан талт болтны хэрэглэл M10Зургаан талт болтны хэрэглэл M104 ширхэг
Фланцтай холхивчФланцтай холхивч2 ширхэг
Ганан гол 30 ммГанан гол 30 мм1 ширхэг
Фанер хуудасФанер хуудас1 ширхэг
Модны цавууМодны цавуу1 ширхэг
#8 × 1" модны шураг#8 × 1" модны шураг12 ширхэг

Шаардлагатай багаж:

Төмөр хөрөөТөмөр хөрөө
Дүрд (гар дүрд)Дүрд (гар дүрд)
Ширээний хавчаарШирээний хавчаар
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Хөрөө (лобзик)Хөрөө (лобзик)
Тохируулгатай түлхүүрТохируулгатай түлхүүр
7

Strap F and thumb screw E

Bend a 30 x 5 mm flat bar into a bridge over the head block, 80 mm from the frames, and screw its legs to the guide block's sides. Drill its top for an M8 rod, run a nut onto the rod under the strap, and lock a wing nut on top as the thumb screw. Turn it down to clamp the head block.

Энэ алхмын материал:

Зөөлөн ганы хавтгай туйванЗөөлөн ганы хавтгай туйван1 ширхэг
#8 × 1" модны шураг#8 × 1" модны шураг4 ширхэг
Эрчилсэн савааЭрчилсэн саваа1 ширхэг
Зургаан талт эрэгЗургаан талт эрэг2 ширхэг
Эрвээхэй гайкаЭрвээхэй гайка1 ширхэг

Шаардлагатай багаж:

Ширээний хавчаарШирээний хавчаар
Төмөр хөрөөТөмөр хөрөө
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
8

Carriage D and platform K

Bolt two 70 mm side bars, 865 mm long, to the head block's side, 330 mm apart, and join their far ends with a cross tie with a caster under its middle as the roller. Drill each bar twice for M12 rods (screws I), 360 mm apart; fix each rod with a nut above and below the bar. Run a nut down each rod, lay an 18 mm plywood platform 430 x 440 mm on them, and lock it with a second nut on top.

Энэ алхмын материал:

Зөөлөн мод 70x70 ммЗөөлөн мод 70x70 мм2 ширхэг
Зургаан талт болтны хэрэглэл M10Зургаан талт болтны хэрэглэл M104 ширхэг
Эргэдэг дугуйн иж бүрдэлЭргэдэг дугуйн иж бүрдэл1 ширхэг
Эрчилсэн савааЭрчилсэн саваа4 ширхэг
Зургаан талт эрэгЗургаан талт эрэг16 ширхэг
Хавтгай угаагуурХавтгай угаагуур8 ширхэг
Фанер хуудасФанер хуудас1 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Тохируулгатай түлхүүрТохируулгатай түлхүүр
ВатерпасВатерпас
9

Arm X and the rope belt

Bolt a 140 mm flat-bar arm X with a 20 mm slot to a collar on the pulley shaft's end. Stand a crank churn on the platform and raise or lower the platform's nuts until its crank shaft is level with the pulley shaft and its handle V sits in the slot. Splice 12 mm cotton rope into a loop about 5 m long round both grooves (see the notebook), with the head slid towards the wheel.

Энэ алхмын материал:

Зөөлөн ганы хавтгай туйванЗөөлөн ганы хавтгай туйван1 ширхэг
Зургаан талт болтны хэрэглэл M10Зургаан талт болтны хэрэглэл M101 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка1 ширхэг
Хөвөн олсХөвөн олс6 m

Шаардлагатай багаж:

Төмөр хөрөөТөмөр хөрөө
Дүрд (гар дүрд)Дүрд (гар дүрд)
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Тохируулгатай түлхүүрТохируулгатай түлхүүр
Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
10

The build in 3D

FreeCAD model of this build: the wheel on its posts with the crank, the guide block, pulley head, strap and thumb screw, the carriage with its caster, platform K on its four screws, a stand-in churn and arm X. The rope is not drawn.
Дизайны файлBLENDCC0 - Free
11

Churn

Pour about 10 litres of heavy cream at about 15 °C into the churn. Slide the head away from the wheel until the rope is tight and clamp it with the thumb screw. Turn the wheel steadily, about 10 times a minute, and time it. To stop, loosen the thumb screw and slide the head towards the wheel: the carriage and churn move with it. When the butter comes, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Энэ алхмын материал:

Өтгөн цөцгийӨтгөн цөцгий10 l
Бүдүүн далайн давсБүдүүн далайн давс1 ширхэг
УсУс1 ширхэг

Шаардлагатай багаж:

Цөцгийн тос бүлэх савЦөцгийн тос бүлэх сав
Дотор нь үлдээдэг мэдрэгчтэй термометрДотор нь үлдээдэг мэдрэгчтэй термометр
Секунд хэмжигчСекунд хэмжигч
Дижитал гал тогооны жинДижитал гал тогооны жин
Зэвэрдэггүй ган том хольц аягаЗэвэрдэггүй ган том хольц аяга
12

Troubleshooting

Churn drive troubleshooting.

Flow

Loading...
13

History and honest limits

**Joseph Forsyth** of Wheeling, Ohio County, Virginia (now West Virginia), US 22,022, 9 November 1858, "Operating Churns". He claimed the carriage D combined with the movable platform K. He gave no sizes, named only the "metallic" frames H, and did not say what turns wheel A or what the belt is: our hand crank, plywood wheel and pulley, cotton rope, timber, bearings, rods and caster are ours.

Материал

21

Шаардлагатай багаж

18

Загварын файлууд

1

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...