Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Fused Quartz Tube: Blown from Brazil Pebble in the Oxy-Gas Flame (Shenstone, 1916)
Charlie

Зохиогч

Charlie

4. Арван нэгдүгээр сар 2026DE
16
0
0
0
0

Fused Quartz Tube: Blown from Brazil Pebble in the Oxy-Gas Flame (Shenstone, 1916)

Fused silica stands sudden heating and cooling that would crack glass, but natural quartz splinters violently in a flame. W. A. Shenstone, in The Methods of Glass-Blowing and of Working Silica in the Oxy-Gas Flame (1916), first turns Brazil pebble into a "non-splintering" silica by quenching it from a yellow-red heat, then melts it in an oxy-gas flame into fine rods, wraps the rods round a platinum core into a first tube, and enlarges it with rings of rod blown out. Not given: quantities and times. He advises most workers to start from bought tubes and to learn each stage by practice. Source: W. A. Shenstone (1916), pp. 88-94. Picture: his p. 93.
Дээд шат
Several days of practice

Зааварчилгаа

1

Read Shenstone

"The silica tubes thus made can be cut and broken like glass, they can be joined together before the flame, and they can also be drawn into smaller tubes when softened by heat."
2

Crack the Brazil pebble

Clean the chips of Brazil pebble (rock crystal) thoroughly, heat them in boiling water and drop them into cold water. Repeat until they have cracked enough to break easily with a clean steel pestle or hammer. Hand-pick the fragments and reject any that are not perfectly free from foreign matter.

Энэ алхмын материал:

Уулын болорУулын болор1 as required
УсУс1 as required

Шаардлагатай багаж:

Өндөр ханатай тогооӨндөр ханатай тогоо
Халаах хавтанХалаах хавтан
ХувинХувин
Бөмбөрцөг толгойт алхБөмбөрцөг толгойт алх
3

Make it non-splintering

Heat the pure, transparent pieces to a yellow-red heat in a covered platinum dish in a muffle furnace and plunge them quickly into a deep clean vessel of distilled water. Repeat until they are semi-opaque, friable masses like white enamel. Wash them with distilled water, drain and dry. Now they can go straight into the hottest part of the flame without splintering.

Энэ алхмын материал:

Нэрмэл усНэрмэл ус1 as required

Шаардлагатай багаж:

Цагаан алтан тавагЦагаан алтан таваг
Муфель зуухМуфель зуух
Тигелийн хямсааТигелийн хямсаа
Шилэн аягаШилэн аяга
4

Set up the flame

Use an efficient oxy-gas burner fed with coal gas and oxygen from a bottle fitted with a gauge and regulator; watch the oxygen used. Protect your eyes with very dark glasses, so dark that work is a little difficult at first, and keep a second pair for long spells, as the glasses get hot. The hottest spot is near the tip of the inner cone: bring the work exactly there.

Энэ алхмын материал:

Нүүрсний хийНүүрсний хий1 as required
ХүчилтөрөгчХүчилтөрөгч1 as required

Шаардлагатай багаж:

Хүчилтөрөгч-нүүрсний хийн шатаагчХүчилтөрөгч-нүүрсний хийн шатаагч
Даралтат хийн баллонДаралтат хийн баллон
Даралт бууруулах тохируулагчДаралт бууруулах тохируулагч
Даралтын хэмжүүрДаралтын хэмжүүр
Тогоочин зуухны харанхуй шилТогоочин зуухны харанхуй шил
5

Draw fine rods

Hold a fragment in platinum-tipped forceps and melt one corner. Press a second fragment against the melted part until they stick, and heat from below upwards (to avoid bubbles) until it is clear. Add a third, a fourth and so on until you have an irregular rod. Reheat it in sections and draw it out into rods or coarse threads 1 to 2 mm across.

Шаардлагатай багаж:

Цагаан алтан үзүүртэй хямсааЦагаан алтан үзүүртэй хямсаа
Хүчилтөрөгч-нүүрсний хийн шатаагчХүчилтөрөгч-нүүрсний хийн шатаагч
Тогоочин зуухны харанхуй шилТогоочин зуухны харанхуй шил
6

Make the first tube

Bind a few rods round a platinum rod about 1 mm across with platinum wires at both ends. Withdraw the core slightly from one end and heat gradually from there until a rough tube 4 to 5 cm long has formed. Close one end, blow it into a small bulb, fix a silica rod to the far end of the bulb, reheat and draw it out into a fine tube. Blow a fresh bulb on one end and draw it out again, until the tube is 6 to 8 cm long.

Шаардлагатай багаж:

Платин утасПлатин утас
Цагаан алтан үзүүртэй хямсааЦагаан алтан үзүүртэй хямсаа
Хүчилтөрөгч-нүүрсний хийн шатаагчХүчилтөрөгч-нүүрсний хийн шатаагч
Тогоочин зуухны харанхуй шилТогоочин зуухны харанхуй шил
7

Blow without soiling it

Blow through a rubber tube on the open end of the silica tube, with a glass tube loosely packed with granulated potash between your mouth and the work so the inside stays clean. Do not take a hot bulb out of the flame to blow it; move it just off the hot spot. Mend holes with plastic silica from the softened end of a fine rod and blow the lump out. Keep the silica clean: a white crust that forms is removed by reheating, but dust or handling can spoil the surface for good.

Шаардлагатай багаж:

Резинэн хоолойРезинэн хоолой
Шилэн хоолойШилэн хоолой
Калийн карбонат (поташ)Калийн карбонат (поташ)
Хүчилтөрөгч-нүүрсний хийн шатаагчХүчилтөрөгч-нүүрсний хийн шатаагч
8

Enlarge and lengthen

To widen a bulb into a tube, lay a ring of fine rod round its end, heat the ring and the end until soft and blow; repeat until the bulb becomes a short tube. For a long tube make several pieces 200 to 250 mm long at the diameter you need and join them end to end. Thicken a tube by adding rings and blowing them out. For a large tube, set a plate of silica behind the work to throw the flame back onto its far side.

Шаардлагатай багаж:

Хүчилтөрөгч-нүүрсний хийн шатаагчХүчилтөрөгч-нүүрсний хийн шатаагч
Цагаан алтан үзүүртэй хямсааЦагаан алтан үзүүртэй хямсаа
Тогоочин зуухны харанхуй шилТогоочин зуухны харанхуй шил
9

History and honest limits

Thorpe's Dictionary (vol. IV, 1913) records Gaudin spinning fused silica threads in 1839, Boys making quartz fibres in 1887, and Shenstone showing in 1901 how to make tubes and bulbs before the oxy-coal-gas blowpipe. Shenstone gives no quantities or times and says most workers save time and money by starting from bought silica tubes. A finished tube holds a little moisture and nitric peroxide; he removes them by heating it and drawing filtered air through, not by washing.

Материал

5
  • Түр орлуулагч
  • 1 as required
    Түр орлуулагч
  • 1 as required
    Түр орлуулагч
  • Түр орлуулагч
  • Түр орлуулагч

Шаардлагатай багаж

18

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...