Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)
Forge

Зохиогч

Forge

13. Арван нэгдүгээр сар 2026NO
9
0
0
0
0

Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)

Henry Gibbs of Chicago received US 683,645, dated 1 October 1901, for a lawn sprinkler "operating on the familiar Barker's mill principle": water leaving its arms sideways pushes the head round. His head turns on a ring of steel balls held in matching grooves in the head and in the end of the supply pipe, so it spins freely with little friction and stays on. We turn the head from brass and the groove in a steel pipe on the lathe. All sizes are ours.
Дунд шат
About 5 hours

Зааварчилгаа

1

How many balls

Jupyter дэвтэр ачаалж байна…
2

Read US 683,645

"It being only necessary that certain of the orifices shall discharge the water tangentially to revolve the head 14 and spray-pipes 15 in the well-known manner."
3

Groove the supply pipe

Chuck a length of steel pipe (his pipe 13) and finish its top end smooth and round. Cut a half-round groove (his 17) round it a little below the end, to the depth the notebook gives, with a round-nosed tool. Use thick-walled pipe, so at least 1.5 mm of wall is left under the groove (ours).

Энэ алхмын материал:

Ган хоолой (зузаан ханатай, эргэлдэх сүвтэй үзүүртэй)Ган хоолой (зузаан ханатай, эргэлдэх сүвтэй үзүүртэй)1 ширхэг

Шаардлагатай багаж:

Металл эрэгМеталл эрэг
Гурван эрүүт токарийн патронГурван эрүүт токарийн патрон
Эргүүлэх машины хэрчих хэрэгсэлЭргүүлэх машины хэрчих хэрэгсэл
Дижитал штангенциркуль 6 инчДижитал штангенциркуль 6 инч
4

Turn the head

Turn a brass bar to a short round head (his 14). Bore it from below to loosely fit the pipe end, his bore 16, but stop short of the top so a lip (his flange 22) overhangs the pipe end. Cut a matching groove 18 inside the bore at the same height as the pipe's groove.

Энэ алхмын материал:

Гуулин дугуй туйванГуулин дугуй туйван1 ширхэг

Шаардлагатай багаж:

Металл эрэгМеталл эрэг
Гурван эрүүт токарийн патронГурван эрүүт токарийн патрон
Эргүүлэх машины хэрчих хэрэгсэлЭргүүлэх машины хэрчих хэрэгсэл
Төвлөх өрөмний багцТөвлөх өрөмний багц
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Дижитал штангенциркуль 6 инчДижитал штангенциркуль 6 инч
5

Drill the ball hole and the arms

Drill a hole (his opening 20) through the head's side into the groove, just bigger than a ball, and tap it for a screw plug (21). Drill three holes round the head into the bore for the spray pipes.

Шаардлагатай багаж:

Суурин өрөмСуурин өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Эрчлээ огтлох иж бүрдэлЭрчлээ огтлох иж бүрдэл
Ширээний хавчаарШирээний хавчаар
6

Make the spray pipes

Cut three lengths of copper tube, close their outer ends, and bend the last bit of each upward as his Fig. 1. Drill small holes near the ends, some pointing sideways (tangentially), all the same way round, so the jets turn the head. Solder the pipes into the head's holes (ours; he threads them in).

Энэ алхмын материал:

Зэс хоолойЗэс хоолой1 ширхэг
Цагаан тугалга-хар тугалганы гагнуурЦагаан тугалга-хар тугалганы гагнуур1 ширхэг
ФлюсФлюс1 ширхэг

Шаардлагатай багаж:

Төмөр хөрөөТөмөр хөрөө
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Суурин өрөмСуурин өрөм
Цахилгаан гагнуурын индүүЦахилгаан гагнуурын индүү
Ширээний хавчаарШирээний хавчаар
7

Assemble with the balls

Slide the head onto the pipe end with the grooves level. Feed balls in through the side hole, turning the head, until the race is full; then screw in the plug. The head should spin freely and not lift off.

Энэ алхмын материал:

Ган бөмбөлөгт холхивчуудГан бөмбөлөгт холхивчууд1 ширхэг
Машины шурагМашины шураг1 ширхэг

Шаардлагатай багаж:

Тохируулгатай түлхүүрТохируулгатай түлхүүр
8

Make the stand

Bore a hardwood block to hold the pipe upright and glue in three splayed dowel legs (ours; his base 10 and supports 11). Screw the hose coupling onto the pipe's lower end below the block (his coupling 12).

Энэ алхмын материал:

Хатуу модны блокХатуу модны блок1 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг
Модны цавууМодны цавуу1 ширхэг
Хоолойн түргэн холбогчХоолойн түргэн холбогч1 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Суурин өрөмСуурин өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
9

Run it

Connect a garden hose and turn on the water slowly: the jets push the head round and throw the water in a circle. More pressure turns it faster.
10

Troubleshooting

Lawn sprinkler troubleshooting.

Flow

Loading...
11

History and honest limits

**Henry Gibbs** of Chicago, assignor to W. D. Allen Manufacturing Company, US 683,645, dated 1 October 1901, filed 20 May 1901. He claimed a single-piece hollow coupling with radial spray pipes having tangential orifices, a bore loosely fitting the supply pipe, "annular grooves in the opposed cylindrical faces of said bore and said pipe" and "bearing balls interposed in said grooves". He gives no sizes or metals; the brass, steel pipe, ball size, soldered copper arms and the wooden stand are ours.

Материал

11

Шаардлагатай багаж

13

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...