Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Hearing Protection (Ear Defenders): Rigid Cups on Liquid-Filled Cushions (Shaw & Thiessen, NRC, US 2,801,423, 1957)
Tex

Зохиогч

Tex

3. Арван нэгдүгээр сар 2026FO
8
0
0
0
0

Hearing Protection (Ear Defenders): Rigid Cups on Liquid-Filled Cushions (Shaw & Thiessen, NRC, US 2,801,423, 1957)

Ear muffs that seal well and still stop low-pitched noise. Each ear is covered by a rigid cup on a cushion made of a thin PVC tube, emptied of air and part-filled with liquid. Pressed on, the liquid flows round the whole rim and fits the cushion to the head, yet cannot compress, so the cup does not vibrate as a whole and pass the sound in. A sprung headband with a pad holds the cups on ball joints. Result: circumaural ear defenders effective against low-frequency noise. Source: E. A. G. Shaw and G. J. Thiessen (National Research Council of Canada), US 2,801,423 (1957). Unknown: sizes and the attenuation achieved. Picture: the patent drawing.
Дунд шат
Unknown

Зааварчилгаа

1

Make the cups

Make two rigid, non-porous cups to go over the ears, of wood, a hard plastic or a light metal such as aluminium. Widen each rim to about the width of the cushion, and make a small hole in the rim for the cushion's filling nipple. Fix a ball joint on the back of each cup. Not given: sizes.

Энэ алхмын материал:

Тодорхойгүй материалТодорхойгүй материал2 аяга
Тодорхойгүй металлТодорхойгүй металл2 ball joints

Шаардлагатай багаж:

Металл эрэгМеталл эрэг
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
2

Make the liquid cushions

For each cup make an endless tube of thin, pliable but non-stretching plasticised PVC, 0.005 to 0.01 in thick, with a filling nipple. Draw out almost all the air, then fill it with liquid to more than a quarter but well under the whole of its cross-section: enough to reach right round the rim when pressed, not so much that it cannot seal. Fix it on the rim with the nipple in the hole. Ours: water as the liquid. Not given: tube size.

Энэ алхмын материал:

PVC хуудасPVC хуудас1 thin plasticised PVC tube
УсУс1 filling

Шаардлагатай багаж:

Тариурын багцТариурын багц
3

Fit the headband and wear them

Make a resilient headband frame with a sponge-rubber pad at its middle and a wire loop at each end. Through each loop pass a threaded stub from the cup's ball joint, with a washer, and tighten with a wing nut. Put the cups over the ears: the cushions take the shape of the head and seal, while the cups stay still against the low-frequency sound. Ours: spring steel for the frame.

Энэ алхмын материал:

Пүршний ган утасПүршний ган утас1 frame and loops
Тодорхойгүй материалТодорхойгүй материал1 sponge rubber pad
Тодорхойгүй металлТодорхойгүй металл2 threaded stubs
Хавтгай угаагуурХавтгай угаагуур2 ширхэг
Эрвээхэй гайкаЭрвээхэй гайка2 ширхэг

Шаардлагатай багаж:

Дугуй хошуут хавчаарДугуй хошуут хавчаар

Материал

7

Шаардлагатай багаж

4

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...