УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
НОГООН ИРЭЭДҮЙ
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ

Building a Langspil — The Icelandic Drone Zither
Build Iceland's traditional drone zither: a long wooden soundbox with one fretted melody string and two drone strings that ring constantly beneath the tune, so a single player makes melody and harmony at once. A serious maker build in the drone zither and how a soundbox amplifies strings.
Дунд шат
Several hours over a few sessions
Зааварчилгаа
1
1
Melody and drone from one box
Melody and drone from one box
The langspil is Iceland's drone zither: a long soundbox with one fretted melody string and one or two drone strings that ring under every note, so one player sounds a tune AND its harmony at once.
2
2
Cut the soundbox parts
Cut the soundbox parts
Cut a base, two side ribs and two end blocks for a long, narrow box about 80 cm long and 8-10 cm wide. Icelanders used driftwood — pine, birch or oak.
Materials for this step:
Baltic Birch Plywood (1/8 inch, 12x12, 10-Pack)1 ширхэгTools needed:
Hacksaw3
3
Glue the box frame
Glue the box frame
Glue the two ribs to the base and end blocks to make a long, shallow open box. Clamp it and let the glue set fully.
Materials for this step:
PVA Wood Glue1 ширхэг4
4
Fit the soundboard
Fit the soundboard
Glue a thin softwood soundboard over the top, overlapping the ribs slightly, to seal a resonant chamber. A thin, light top vibrates best.
Materials for this step:
Dry Softwood Board1 ширхэг
PVA Wood Glue1 ширхэг5
5
Cut a soundhole
Cut a soundhole
Cut a round soundhole in the soundboard so the sound built up inside the box can escape.
Tools needed:
Sloyd Carving Knife6
6
Drill the peg holes
Drill the peg holes
At the headstock end, bore three tapered holes through the top for the tuning pegs — one for the melody string, two for the drones.
Tools needed:
Awl7
7
Fit the tuning pegs
Fit the tuning pegs
Push a friction tuning peg into each hole so it turns stiffly and holds string tension without slipping.
Materials for this step:
Tuning Pegs3 ширхэг8
8
Carve the nut and bridge
Carve the nut and bridge
Carve a small hardwood nut near the pegs and a low bridge near the far end. The strings ride over both, lifted clear of the soundboard.
Tools needed:
Sloyd Carving Knife9
9
String it
String it
Anchor three steel strings to small pins at the far end, run them over the bridge and nut, and wind each onto its tuning peg.
Materials for this step:
Steel Music Wire1 ширхэг10
10
Set the frets
Set the frets
Fit small metal frets across the soundboard UNDER THE MELODY STRING ONLY, spaced so pressing behind each one gives the next note of a diatonic scale.
Materials for this step:
Fret Wire1 ширхэгTools needed:
Metal File11
11
Tune the drones
Tune the drones
Tune the two drone strings to a low keynote and its octave or fifth. They will sound continuously, giving the langspil its droning voice.
12
12
Tune the melody string
Tune the melody string
Tune the melody string to the keynote too. Check it against the frets — pressing behind each fret should climb cleanly through the scale.
13
13
Play it
Play it
Press the melody string behind the frets with one hand and pluck it with the other. The drones ring under every note. Try bowing or gently hammering it too.
14
14
Compendium — the drone zither
Compendium — the drone zither
The langspil is a drone zither: a resonant box with strings stretched along the top. One fretted MELODY string carries the tune while one or two DRONE strings hold a constant note, so a single player produces melody and harmony together — the same principle as a bagpipe's chanter over its drones, or a hurdy-gurdy. The sealed soundbox is a resonator: the thin strings alone move almost no air, but they shake the light soundboard, which drives the air inside the box, which spills out through the soundhole — the box amplifies the strings, exactly as in a guitar or violin. String pitch follows the same three rules as the musical bow — tension, length and mass — and pressing the melody string just behind a fret shortens its speaking length to raise the pitch by a fixed step, which is the whole point of the frets. Iceland has few trees, so langspils were built from driftwood — pine, birch, oak; the instrument is first recorded in the 18th century and is a northern cousin of the German scheitholt and the Appalachian dulcimer, all box drone zithers. Icelandic schoolchildren still build and play their own today, some laser-cut from plywood in a Fab Lab — a heritage instrument kept alive by making it.
Материал
6- Placeholder
- 2 ширхэгPlaceholder
- 1 ширхэгPlaceholder
- 3 ширхэгPlaceholder
- 1 ширхэгPlaceholder
You can swap these in
Can't get one of the materials? Swap it for an equivalent — these work just as well.
- Instead of Sloyd Carving Knife, try:
Blunt Collection Knife
Gilder's Knife
Knife
Sharp Cinnamon Knife - Instead of PVA Wood Glue, try:
Polyurethane Glue - Instead of Baltic Birch Plywood (1/8 inch, 12x12, 10-Pack), try:
CDX Softwood Plywood
Fire-Rated Plywood - Instead of Steel Music Wire 0.032", try:
Hook-Up Wire - Assortment (Stranded)
Tie Wire
Thin Brass Wire (for cleaning spouts)
Slip Ring - 6 Wire (2A)
Bezel Wire
Холбоотой загварууд
Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим
Related blueprints
Other builds that share materials, tools, or techniques with this one.

Building a Janggu — The Korean Hourglass Drum

Building a Đàn Bầu — Vietnam's One-String Harmonic Zither

Building a Roman Ballista — The Torsion-Powered Bolt Throwerengineering

Building a Clay Kiln — The First Furnacecraft/ceramics-and-clay

Building an Arab Kamal — The Indian Ocean Navigator's Latitude FinderPhysics & Astronomy

Building a Celestial Globe — Mapping the Stars on a SpherePhysics & Astronomy
CC0 Нийтийн домэйн
Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.
Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.