Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Kitchen Funnel with Air-Vent Ribs, 3D Printed in PETG
3DBonanza

Зохиогч

3DBonanza

18. Арван нэгдүгээр сар 2026US
5
0
0
0
0

Kitchen Funnel with Air-Vent Ribs, 3D Printed in PETG

A 120 mm kitchen funnel for bottling wine, cider or juice, printed in one piece in PETG. Three small ribs along the outside of the spout hold it off the bottle neck so air can come out while the liquid goes in, so it pours without glugging. A common, open design; all sizes are ours, and we have not printed or tested it yet.
Анхан шат
About 4 hours, mostly printing

Зааварчилгаа

1

Our funnel's numbers

Jupyter дэвтэр ачаалж байна…
2

Make it fit your bottles

Optional: change TOP_D or the spout sizes and run it in FreeCAD: OUT=. TOP_D= freecadcmd build_all.py
build_all.pypython
"""Batch 2451 -- PETG kitchen funnel with air-vent ribs on the spout. Open, common design (Admiral 2026-11-18: "it is open knowledge on
what a funnel is"); all sizes ours. Run: OUT=<dir> [TOP_D=120] freecadcmd build_all.py  (mm; printed rim-down on the bed, no supports)."""
import math, os
import FreeCAD as App, Part, MeshPart
OUT = os.environ["OUT"]
V = App.Vector
TOP_D = float(os.environ.get("TOP_D", "120"))     # rim inside diameter
WALL = 1.8
CONE_HALF = 30.0                                   # half-angle: 60 degree cone
SPOUT_TOP_D, SPOUT_TIP_D, SPOUT_L = 16.0, 13.0, 50.0   # spout outside, tapering so it fits bottle necks
RIB_H, RIB_W = 1.2, 1.6                            # three vent ribs on the spout's outside
RIM_LIP = 4.0                                      # flat lip round the rim (bed adhesion, stiffness)
r_top = TOP_D / 2
r_neck_in = SPOUT_TOP_D / 2 - WALL
cone_h = (r_top - r_neck_in) / math.tan(math.radians(CONE_HALF))
def save(sh, name):
    bb = sh.BoundBox
    print(name, "valid", sh.isValid(), "solids", len(sh.Solids), "bbox", [round(v, 1) for v in (bb.XLength, bb.YLength, bb.ZLength)],
          "volume_cm3", round(sh.Volume / 1000, 1))
    MeshPart.meshFromShape(Shape=sh, LinearDeflection=0.03, AngularDeflection=0.12).write(os.path.join(OUT, name + ".stl"))
# z up: spout tip at z=0, cone above, rim at the top
off = WALL / math.cos(math.radians(CONE_HALF))
outer = Part.makeCone(SPOUT_TOP_D / 2, r_top + off, cone_h, V(0, 0, SPOUT_L))
inner = Part.makeCone(r_neck_in, r_top, cone_h + 0.01, V(0, 0, SPOUT_L))
spout_o = Part.makeCone(SPOUT_TIP_D / 2, SPOUT_TOP_D / 2, SPOUT_L + 0.01, V(0, 0, 0))
spout_i = Part.makeCone(SPOUT_TIP_D / 2 - WALL, r_neck_in, SPOUT_L + 0.02, V(0, 0, -0.01))
body = outer.fuse(spout_o).cut(inner).cut(spout_i)
lip = Part.makeCylinder(r_top + off + RIM_LIP, 1.6, V(0, 0, SPOUT_L + cone_h - 1.6)).cut(Part.makeCylinder(r_top - 0.5, 3, V(0, 0, SPOUT_L + cone_h - 2)))
body = body.fuse(lip)
r_at = lambda z: (SPOUT_TIP_D + (SPOUT_TOP_D - SPOUT_TIP_D) * z / SPOUT_L) / 2
for a in (0, 120, 240):
    z0, z1 = 2.0, SPOUT_L - 1.0
    pts = [V(r_at(z0) - 0.4, -RIB_W / 2, z0), V(r_at(z0) + RIB_H, -RIB_W / 2, z0), V(r_at(z1) + RIB_H, -RIB_W / 2, z1), V(r_at(z1) - 0.4, -RIB_W / 2, z1)]
    rib = Part.Face(Part.makePolygon(pts + [pts[0]])).extrude(V(0, RIB_W, 0))
    rib.rotate(V(0, 0, 0), V(0, 0, 1), a)
    body = body.fuse(rib)
body = body.removeSplitter()
save(body, "petg-kitchen-funnel")
cap = math.pi * cone_h / 3 * (r_top**2 + r_top * r_neck_in + r_neck_in**2) / 1000
print("cone height", round(cone_h, 1), "mm; holds about", round(cap), "ml in the cone")
print("spout", SPOUT_TOP_D, "->", SPOUT_TIP_D, "mm outside, bore", round(SPOUT_TIP_D - 2 * WALL, 1), "mm at the tip")
print("air gap per rib, in a neck the spout just fits:", RIB_H, "x", "(gap between ribs)")

Шаардлагатай багаж:

Дижитал штангенциркуль 6 инчДижитал штангенциркуль 6 инч
3

Print the funnel

Print it rim down on the bed, no supports; the cone and spout grow upward. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 3 walls.
Дизайны файлSTLCC0 - Free

Энэ алхмын материал:

PETG филаментPETG филамент60 г

Шаардлагатай багаж:

FDM 3D хэвлэгчFDM 3D хэвлэгч
3D хэвлэгчийн цорго багц3D хэвлэгчийн цорго багц
4

Clean it up

Trim any strings or blobs, especially inside the spout and between the ribs. Check the spout is clear.

Шаардлагатай багаж:

Гар урлалын хутгаГар урлалын хутга
5

Check the fit

Put the spout into a bottle: the ribs should touch the neck and leave gaps between them. Pour water through and watch it run without glugging.
Алхам 5 - Image 1

Шаардлагатай багаж:

Бөглөөтэй шилэн шилнүүдБөглөөтэй шилэн шилнүүд
УсУс
6

Sanitise

Soak it in no-rinse sanitiser mixed as its label says. Do not boil it: PETG softens at about 80 °C.

Шаардлагатай багаж:

Ариутгагч бодисАриутгагч бодис
УсУс
7

Troubleshooting

Funnel problems and fixes.

Flow

Loading...
8

Honest limits

A common, open design, drawn by us in FreeCAD; every size is ours. The ribs were checked by slicing the model; the funnel has not been printed or poured through by us yet. Sanitise before every use and replace it when scratched.

Материал

1
  • Түр орлуулагч

Шаардлагатай багаж

7

Загварын файлууд

1

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...