Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Lead Came: Window Rods Cast in a Split Wooden Mould (Theophilus, tr. Hendrie 1847)
Forge

Зохиогч

Forge

4. Арван нэгдүгээр сар 2026NO
12
0
0
0
0

Lead Came: Window Rods Cast in a Split Wooden Mould (Theophilus, tr. Hendrie 1847)

Theophilus' way to cast window leads without an iron mould: a stick of fir is split, a groove marked with a red-dyed flax thread and cut along both halves, the halves bound with a strap and the lead poured in again and again until the hot lead has burnt the groove to the bottom. Each rod is then trimmed in a slotted wooden gauge, cut with a knife on both sides and scraped smooth. Source: Theophilus, De Diversis Artibus, Book II, ch. XXVI, tr. R. Hendrie (1847), pp. 149-151. Picture: p. 151.
Дунд шат
Unknown

Зааварчилгаа

1

Split and mark the wood

Take fir or another wood that splits smoothly, the size of the iron mould (a yard long, two fingers broad, a finger thick). Split it and round the outside. Mark each end of both pieces for the width of the rod. Stretch a thin twisted flax thread wet with red colour from mark to mark on one inner face and press the other piece against it, so the line shows on both; do the same for the second line.

Шаардлагатай багаж:

Тугалган зураасны хэвТугалган зураасны хэв
Маалингын утасМаалингын утас
Гар урлалын хутгаГар урлалын хутга
2

Cut the groove

Cut the groove between the lines with a knife, as wide and deep as you wish, but not through the lower end; leave an opening at the top for pouring.

Шаардлагатай багаж:

Гар урлалын хутгаГар урлалын хутга
Тугалган зураасны хэвТугалган зураасны хэв
3

Cast the rods

Melt the lead as for the iron mould. Bind the two halves together with a strap from top to bottom, hold the mould with a wooden holder and pour in the lead; loosen the strap and take out the rod. Bind and cast again until the burning reaches the bottom of the groove; after that you can cast gently as many as you wish.

Энэ алхмын материал:

Хар тугалганы гулдмайХар тугалганы гулдмай1 pure lead

Шаардлагатай багаж:

Тугалган зураасны хэвТугалган зураасны хэв
Арьсан оосорАрьсан оосор
Шавар тогооШавар тогоо
Модны нүүрсМодны нүүрс
ШанагаШанага
4

Trim the rods

Cut a piece of wood two fingers wide and as thick as the inside of the groove, split in the middle at one end so the rod fits into the slit. With the rod in it, cut it with a knife on both sides, then smooth and scrape it as you like.

Шаардлагатай багаж:

Гар урлалын хутгаГар урлалын хутга

Материал

1

Шаардлагатай багаж

7

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...