Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Leather Knife: the Harnessmaker's Knife, Forged from Cutlery Steel (Holford, 1907)
Forge

Зохиогч

Forge

5. Арван нэгдүгээр сар 2026NO
16
0
0
0
0

Leather Knife: the Harnessmaker's Knife, Forged from Cutlery Steel (Holford, 1907)

The harnessmaker's knife, the broad curved blade saddlers push through leather. Frederick Holford's 20th Century Toolsmith (1907) says it "will try the skill of the expert to its full extent". He cuts it from sheet cutlery steel of 0.75 % carbon, 3/32 inch thick, 4 to 6 inches wide; draws the cutting edge out at a deep cherry red; packs the steel with light blows at a dim red; anneals it in lime or ashes; hardens it from a low cherry red in the bath; and draws the temper to dark blue, the temper he gives for all leather-cutting tools. He gives no handle wood and no outline sizes beyond the width; those are unknown here. Source: F. J. Holford, The 20th Century Toolsmith and Steelworker (1907), pp. 163-166 and p. 21 (the hardening bath). Picture: his Fig. 94.
Дээд шат
A day

Зааварчилгаа

1

Read Holford

"To make one, use sheet cutlery steel of 75 points carbon and 3-32 of an inch thick, but the size of the steel to be used will depend on the size of the knife to be made."
2

Mark and cut the blank

Draw the outline of the knife on the steel, 4 to 6 inches wide or smaller, to suit whoever will use it. Cut it out 3/16 inch smaller than the finished knife along the edge (line a in Fig. 94), because the cutting edge is still to be drawn out. If the steel is too short for the shank, cut it as at b and draw the shank out to shape. Other outline sizes are not given (unknown).

Энэ алхмын материал:

Хутганы гангийн хуудасХутганы гангийн хуудас1 хуудас

Шаардлагатай багаж:

Зурмал зүүЗурмал зүү
Хүйтэн цүүцХүйтэн цүүц
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
3

Draw out the edge

Take a deep cherry red heat and start hammering at the point f, hammering equally from both sides until the whole cutting edge is drawn out. It may take two or three heats.

Шаардлагатай багаж:

Дархны зуухДархны зуух
ДөшДөш
Дархны алхДархны алх
Дархны хавчаарДархны хавчаар
4

Pack the steel and anneal

Bring the knife to a very dim red and hammer evenly on both flat sides of the whole edge. Heat again to a very low heat and hammer again, this time a little back from the edge (line d), to take the strain out of the steel. Then heat the whole knife except the shank to an even blood red and pack it in lime or ashes until perfectly cold. File the edges smooth.

Шаардлагатай багаж:

Хатуу модны үнсХатуу модны үнс
Металлын гилбэрМеталлын гилбэр
5

Harden

Heat the knife to a low cherry red one inch back from the edge in the blaze of the fire, moving it in a circle so the whole edge heats evenly and never in streaks. Plunge the whole knife upright into the hardening bath: clean water free from grease, best made a brine with as much salt as it will dissolve, kept large and cold (Holford, p. 21). An evenly forged and heated knife comes out straight.

Шаардлагатай багаж:

Дархны зуухДархны зуух
Дархны хавчаарДархны хавчаар
Ханасан давсны уусмалХанасан давсны уусмал
Халуунд тэсвэртэй бээлийХалуунд тэсвэртэй бээлий
6

Temper and straighten

Polish one side as far back as it is hardened. Draw the temper very slowly over the fire, moving the knife in a circle, until the polished side shows a dark blue. Before cooling, take out any crook by straightening on the anvil with the hammer, then cool off. If it crooked so much that it cannot be straightened now, heat it again, straighten and anneal, and start the hardening again.

Шаардлагатай багаж:

Эмерийн даавууЭмерийн даавуу
Дархны зуухДархны зуух
ДөшДөш
Дархны алхДархны алх
7

Grind and handle

Grind the edge; what crook is left can be taken out in grinding. Feather the shank with a very sharp cold chisel so it stays firm, and drive it into a wooden handle (the dotted outline e). The handle wood is not given (unknown).

Энэ алхмын материал:

Ишний хатуу модон бэлдэцИшний хатуу модон бэлдэц1 handle

Шаардлагатай багаж:

Эргэдэг хурцлах чулууЭргэдэг хурцлах чулуу
Хүйтэн цүүцХүйтэн цүүц
8

History and honest limits

Holford wrote for blacksmiths and toolmakers who forged their own tools; he says a well-made knife "will hold a very keen edge on the hardest of leather". The same dark-blue temper, he says, applies to all leather-cutting tools. The handle wood and the outline sizes beyond the width are not given; a hardwood handle stands for the handle, and a cold chisel is our tool for cutting out the blank.

Материал

2

Шаардлагатай багаж

13

Энэ загвараар хийдэг

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...