Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Front Horseshoe Forged in Two Heats: Bend, Bevel, Concave, Fuller and Punch (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)
Forge

Зохиогч

Forge

13. Арван нэгдүгээр сар 2026NO
3
0
0
0
0

Front Horseshoe Forged in Two Heats: Bend, Bevel, Concave, Fuller and Punch (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)

A flat front horseshoe made from one iron bar, as taught at the Dresden shoeing school: bend each branch over the anvil, bevel and flatten it, concave the hoof side, fuller the crease, and stamp and pritchel the nail holes. From Lungwitz and Adams, A Text-Book of Horseshoeing (11th edition, 1913). "Any ordinary shoe can and should be completed in the rough in two heats." Fitting and nailing the shoe to the horse are not covered here.
Дунд шат
8-15 minutes a pair, once practised

Зааварчилгаа

1

Bar length and sizes

Jupyter дэвтэр ачаалж байна…
2

Read Lungwitz and Adams

"A shoe should be made thoughtfully, but yet quickly enough to make the most of the heat."
3

Measure the hoof

Measure the length of the hoof from the point of the toe to the buttress, and its greatest width. Added together they give the length of the bar. To keep the exact outline, set the hoof on stiff paper and trace round the wall with a pencil.

Шаардлагатай багаж:

Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
ХарандааХарандаа
Зузаан цаасны хуудасЗузаан цаасны хуудас
4

Cut the bar

Choose good, tough iron, of a width and thickness that needs the least working. Cut the bar to the length you measured; a bar shoe or a shoe with heel calks needs a longer bar.

Энэ алхмын материал:

Давтсан төмөр гулдмайДавтсан төмөр гулдмай1 ширхэг

Шаардлагатай багаж:

Дархны зуухДархны зуух
Дөшний огтлох ишДөшний огтлох иш
Дархны хямсааДархны хямсаа
Дугуйруулах алхДугуйруулах алх
5

Bend the outer branch

Heat the bar white-hot just beyond its middle. Lay the head of the sledge across one end of the anvil face, hold the cold end of the bar on it with the hot end on the face, and bend the bar into a half-circle with the round head of the turning hammer. Make the outer branch first, and the right shoe first in a pair. Draw out the end to width and thickness with the sledge.

Шаардлагатай багаж:

Дархны зуухДархны зуух
Хушуут жижиг дөшХушуут жижиг дөш
ЧаргаЧарга
Дугуйруулах алхДугуйруулах алх
Дархны хямсааДархны хямсаа
6

Bevel and flatten

Lay the bent branch obliquely across the heel of the horn, turn it to the right onto an edge, and bevel it diamond-shaped from toe to end. Flatten it on the face: bending stretched and thinned the outer edge and thickened the inner one, so leave the inner edge a trifle thinner. Go over it lightly on the horn with the flat face of the hammer to shape it.

Шаардлагатай багаж:

Хушуут жижиг дөшХушуут жижиг дөш
Дугуйруулах алхДугуйруулах алх
Дархны хямсааДархны хямсаа
7

Concave and fuller

Concave (seat) the hoof side, ending about 3/4 in from the end of the branch, or leave it flat for an arched sole. Turn the branch and fuller it: set the fuller about 1/12 in from the edge on small shoes, more on large ones, and lead it from the end of the branch to the toe, twice, to about two-thirds of the thickness.

Шаардлагатай багаж:

Хушуут жижиг дөшХушуут жижиг дөш
ЧаргаЧарга
Фуллер (ховил гаргах төмөр)Фуллер (ховил гаргах төмөр)
Дугуйруулах алхДугуйруулах алх
Дархны хямсааДархны хямсаа
8

Stamp and pritchel the nail holes

Stamp the nail holes in the crease and punch them through with the pritchel. Six are enough for a medium shoe, all in the front half and none at the toe. Their distance from the outer edge equals the thickness of the wall there; incline the toe holes a little inward and punch the quarter holes straight. Each hole tapers from the ground side to the hoof side.

Шаардлагатай багаж:

Хушуут жижиг дөшХушуут жижиг дөш
Халуун цоолтуурХалуун цоолтуур
Тахны хадаасны нүх гаргах цоолтуурТахны хадаасны нүх гаргах цоолтуур
Дугуйруулах алхДугуйруулах алх
Дархны хямсааДархны хямсаа
9

Finish the branch, then the other

Run over the surfaces, go over the outer edge on the horn, and hammer the bearing surface smooth and level. Make the inner branch the same way, turned to the left and fullered from toe to heel. The finished front shoe is round at the toe and about 7/16 in thick; a hind shoe is bent more pointed at the toe and needs no concaving, only the inner edge rounded.

Шаардлагатай багаж:

Дархны зуухДархны зуух
Хушуут жижиг дөшХушуут жижиг дөш
Дугуйруулах алхДугуйруулах алх
Фуллер (ховил гаргах төмөр)Фуллер (ховил гаргах төмөр)
Халуун цоолтуурХалуун цоолтуур
Тахны хадаасны нүх гаргах цоолтуурТахны хадаасны нүх гаргах цоолтуур
Дархны хямсааДархны хямсаа
10

Troubleshooting

Horseshoe troubleshooting.

Flow

Loading...
11

History and honest limits

From **A Text-Book of Horseshoeing, for Horseshoers and Veterinarians**, by A. Lungwitz (Dresden shoeing school) and John W. Adams (University of Pennsylvania), 11th edition, J. B. Lippincott, 1913 (Project Gutenberg 66786), chapter III F, "Making Shoes"; wall thicknesses after Mayer. Not covered: trimming, fitting and nailing the shoe to the hoof, clips, calks and special shoes. The book names no forge fuel. The metric figures are ours.

Материал

1

Шаардлагатай багаж

12

Энэ загвараар хийдэг

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...