Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Pendulum Twin-Dasher Churn: A Swinging Weighted Lever Rocks a Beam That Works Two Half-Dashers Alternately
Martin

Зохиогч

Martin

9. Арван нэгдүгээр сар 2026NO
11
0
0
0
0

Pendulum Twin-Dasher Churn: A Swinging Weighted Lever Rocks a Beam That Works Two Half-Dashers Alternately

James O. Merrill of Chichester, New Hampshire, received US 23,986, dated 10 May 1859, for an oscillating churn light enough to be worked by a child. A weighted pendulum behind the frame rocks a shaft; on its front end a beam rocks, and two links from the beam's ends work two dasher arms up and down in turn through slots in a guide bar. Each arm carries a half-round dasher pierced with holes, so the two halves fill the barrel. The two-piece cover is held down by a thumb screw. This rung builds it full size in timber over a 20-litre bucket.
Дунд шат
About 2 days

Зааварчилгаа

1

How far the dashers move

Jupyter дэвтэр ачаалж байна…
2

Two dashers worked in turn, before it

Mitchell's lever worked two dashers in turn; Merrill's weighted pendulum keeps them going with less effort.
3

Read US 23,986

"... the operator oscillates the lever L, which communicates the motion through the vibrating shaft M, the vibrating lever E, the auxiliary levers F, F', to the dasher arms G, G', thus producing an alternate reciprocating action of the dashers N, N'".
4

Base and frame

Cut a pine base A 720 x 520 mm. Stand two side pieces B B' of 44 x 70 mm timber 960 mm tall, 400 mm apart, 200 mm from the base's back edge, with diagonal side braces I I' and front braces H H' to the base. Screw top braces C C' (444 x 60 x 22 mm) across the front and back faces of the side pieces at the top, and bore both 21 mm in the middle, 30 mm below their top edge.

Энэ алхмын материал:

Нарсан банзНарсан банз2 ширхэг
Зөөлөн мод 70x70 ммЗөөлөн мод 70x70 мм4 ширхэг
#10 x 3" модны шураг#10 x 3" модны шураг30 ширхэг
Модны цавууМодны цавуу1 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Утасгүй өрөмУтасгүй өрөм
Хүрзэн өрмийн үзүүрийн багцХүрзэн өрмийн үзүүрийн багц
ХавчааруудХавчаарууд
ВатерпасВатерпас
Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
5

Shaft M, lever E and pendulum L

Screw a hardwood bearing block 80 x 80 x 18 mm, bored 20.5 mm, over each hole. Cut a 20 mm steel shaft 310 mm long and pass it through both. On its front end fix a hardwood lever E 400 x 60 x 20 mm at its middle with a bolt across, drilled 8.5 mm 150 mm each side of the middle for the pins c. On its back end fix the pendulum L, a hardwood bar 50 x 20 mm, 810 mm long, 60 mm below its top. Glue a 24 mm dowel handle h into L 180 mm below the shaft and bolt an 8 kg kettlebell to its foot as W.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз2 ширхэг
Модны шурагМодны шураг8 ширхэг
Ган түүхий голГан түүхий гол1 ширхэг
Зургаан талт болтны цуглуулгаЗургаан талт болтны цуглуулга3 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка3 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг
Модны цавууМодны цавуу1 ширхэг
Гиртэй жинГиртэй жин1 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Хүрзэн өрмийн үзүүрийн багцХүрзэн өрмийн үзүүрийн багц
Төмөр хөрөөТөмөр хөрөө
Тохируулгатай түлхүүрТохируулгатай түлхүүр
6

Guide bar J, arms G and links F

Bolt a hardwood guide bar J 444 x 40 x 36 mm across the side pieces' fronts on spacer blocks so it stands 70 mm in front of them, 530 mm above the base, and cut two 27 mm square slots through it 40 mm apart. Cut two hardwood dasher arms G G' 25 mm square and 580 mm long, drop them through the slots, and drill each 8.5 mm 20 mm below its top. Cut two links F F' 30 x 14 mm with holes 282 mm apart and bolt each from a pin c on E to a pin g on an arm, with washers and lock nuts so they turn freely.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз2 ширхэг
Зургаан талт болтны цуглуулгаЗургаан талт болтны цуглуулга6 ширхэг
Хавтгай угаагуурХавтгай угаагуур8 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка4 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Модны цүүцнүүдМодны цүүцнүүд
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Тохируулгатай түлхүүрТохируулгатай түлхүүр
7

Barrel D, covers, dashers and thumb screw

Stand a food-grade 20-litre bucket on the base under the arms. Cut two half-discs N N' 240 mm across from 12 mm plywood, each with three 34 mm holes, and screw one under each arm's foot. Cut two half-round covers m m from 12 mm plywood to fit the bucket's top, notched for the arms. Bolt a cross brace K 444 x 40 x 30 mm across the side pieces' fronts 440 mm above the base, drill it for an M8 rod 72 mm behind the arms, and run the rod through a nut in K with a wing nut on top as the thumb screw i, down onto an oblong block l laid across both covers.

Энэ алхмын материал:

20 литрийн хувин20 литрийн хувин1 ширхэг
Фанер хуудасФанер хуудас2 ширхэг
Модны шурагМодны шураг6 ширхэг
Хатуу модон банзХатуу модон банз1 ширхэг
Зургаан талт болтны цуглуулгаЗургаан талт болтны цуглуулга2 ширхэг
Эрчилсэн савааЭрчилсэн саваа1 ширхэг
Зургаан талт эрэгЗургаан талт эрэг1 ширхэг
Эрвээхэй гайкаЭрвээхэй гайка1 ширхэг

Шаардлагатай багаж:

Хөрөө (лобзик)Хөрөө (лобзик)
Нүх хөрөөдөгч багцНүх хөрөөдөгч багц
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Халив иж бүрдэлХалив иж бүрдэл
Тохируулгатай түлхүүрТохируулгатай түлхүүр
8

The build in 3D

FreeCAD model of this build, a quarter of the barrel and covers cut away: the base and frame with its braces, shaft M with lever E in front and the weighted pendulum behind, links F, the arms in guide bar J, the two half-dashers in the barrel, and the thumb screw on its block. It was checked at five pendulum angles from -12 to +12 degrees.
Дизайны файлBLENDCC0 - Free
9

Churn

Lift the front cover, pour in about 10 litres of heavy cream at about 15 °C, checked with the thermometer, put the cover back and turn the thumb screw down on the block. Swing the pendulum by its handle about 12 degrees each way and time it: the half-dashers rise and fall in turn. When the butter comes, slacken the screw, unbolt the dashers, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Энэ алхмын материал:

Өтгөн цөцгийӨтгөн цөцгий10 l
Бүдүүн далайн давсБүдүүн далайн давс1 ширхэг
УсУс1 ширхэг

Шаардлагатай багаж:

Дотор нь үлдээдэг мэдрэгчтэй термометрДотор нь үлдээдэг мэдрэгчтэй термометр
Секунд хэмжигчСекунд хэмжигч
Дижитал гал тогооны жинДижитал гал тогооны жин
Зэвэрдэггүй ган том хольц аягаЗэвэрдэггүй ган том хольц аяга
10

Troubleshooting

Pendulum churn troubleshooting.

Flow

Loading...
11

History and honest limits

**James O. Merrill** of Chichester, Merrimack County, New Hampshire, assignor to Wm. A. Swain, US 23,986, 10 May 1859, "Churn". He meant it to take the labour out of churning, adapted to the strength of a child, and claimed the pendulum and weight with the shaft, beam, links and the two alternate dasher arms. He gave no sizes or weight: the frame, the 8 kg weight, the 12 degree swing and every size are ours.

Материал

20

Шаардлагатай багаж

17

Загварын файлууд

1

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...