Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Pop Rivets: Copper Hollow Rivet on a Steel Break Mandrel with a Ring-Cutter Head (Kraemer, US 3,257,890)
Charlie

Зохиогч

Charlie

31. Аравдугаар сар 2026DE
8
0
0
0
0

Pop Rivets: Copper Hollow Rivet on a Steel Break Mandrel with a Ring-Cutter Head (Kraemer, US 3,257,890)

A blind rivet set from one side. Kraemer's mandrel head has a sharp ring edge that shears the inner part of the rivet's tail and pushes it into the bore, while the outer part folds round the head. The pull needed is about half, and the set rivet is about as strong in shear as a solid one. Result: copper pop rivets, 3, 4 or 5 mm, each on its steel mandrel. Source: Kraemer, US 3,257,890 (1966). His other rivet metals, aluminium-magnesium and 80/20 copper-nickel, are separate compositions. Not given: die design. Picture drawn by Youblob.
Дээд шат
Factory process

Зааварчилгаа

1

Stamp the copper rivet

Form a hollow rivet with a flange (set head) at one end and a straight bore. Kraemer says the parts can be made e.g. by stamping. Sizes (mm), outside / bore: 5 / 3, 4 / 2.6, 3 / 1.8. Ours: from copper sheet.

Энэ алхмын материал:

Зэсэн хуудасЗэсэн хуудас1 as required

Шаардлагатай багаж:

Штамплах шахуургаШтамплах шахуурга
2

Form the steel mandrel

Shape a steel mandrel: draw shaft, a groove as the breaking point, a cone tapering up to the bore size, and a near-hemispherical button head. Head edge diameter (mm): 4.3, 3.6, 2.6 for the 5, 4, 3 mm rivets, so it covers 55-70 % of the rivet's end face. Ours: from steel wire.

Энэ алхмын материал:

Ган утасГан утас1 as required

Шаардлагатай багаж:

Штамплах шахуургаШтамплах шахуурга
3

Assemble and size for the work

Push the mandrel fully into the rivet; it is supplied this way. Pick a length that sticks out past the sheets by 3-5 mm (5 mm rivet), 2.5-3.5 mm (4 mm) or 2-4 mm (3 mm).

Шаардлагатай багаж:

Ривет буугийн багцРивет буугийн багц
4

Set it from one side

Put the rivet in the hole, grip the draw shaft and press the tool's head on the flange while pulling. The ring edge shears the tail, the rest bulges and folds round the button head, and the mandrel breaks at its groove.

Шаардлагатай багаж:

Ривет буугийн багцРивет буугийн багц

Материал

2
  • Түр орлуулагч
  • 1 as required
    Түр орлуулагч

Шаардлагатай багаж

2

Энэ загвараар хийдэг

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...