Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Push Button: Normally Open Momentary Switch with a Cushioned Contact (De Reamer, GE 1939)
English
Ed

Зохиогч

Ed

28. Аравдугаар сар 2026FI
14
0
0
0
0

Push Button: Normally Open Momentary Switch with a Cushioned Contact (De Reamer, GE 1939)

A panel push button that closes a circuit only while you press it. A spring holds the button out, and a metal rim on the end of its rod sits clear of two contacts. Press it and the rim bridges both contacts. A second spring inside the button lets the rod give, so the contacts never take more than that spring's force. Source: Frank C. De Reamer, US 2,166,803 (General Electric, 1939), Fig. 5. Unknown: the insulating material, the metals and every size. De Reamer gives none of them, so they are linked to unknown heads. The tools are ours. Picture: the patent's Fig. 5.
Дээд шат
2 days

Зааварчилгаа

1

Mould the housing

Mould a cup-shaped housing of insulating material, with a boss on each of two opposite sides, a recess in the top of each boss, a groove inside below each boss, and a bead round the top. Unknown: the material, the sizes and the moulding.

Энэ алхмын материал:

Тодорхойгүй тусгаарлагч материалТодорхойгүй тусгаарлагч материал1 as required

Шаардлагатай багаж:

Шахаж хэвлэх хэвШахаж хэвлэх хэв
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
2

Make the terminals and contacts

Bend two angled metal strips. The upper end of each sits in a boss recess, and the lower end is a solder lug. Fix each upper end to a contact that fits the groove inside the housing, stepped at its bottom end. Unknown: the metal.

Энэ алхмын материал:

Тодорхойгүй металлТодорхойгүй металл1 as required

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Хавтгай хошуут хямсааХавтгай хошуут хямсаа
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
3

Make the sleeve, plate and cover

Turn a threaded sleeve and cut its thread. Spin its lower end over onto a metal plate with tangs. Cut a cover of insulating sheet with ears that reach over the bosses and a hole in the middle to guide the rod.

Энэ алхмын материал:

Тодорхойгүй металлТодорхойгүй металл1 as required
Тодорхойгүй тусгаарлагч материалТодорхойгүй тусгаарлагч материал1 as required

Шаардлагатай багаж:

Металл эрэгМеталл эрэг
Токарийн багажны багц (HSS)Токарийн багажны багц (HSS)
Гадна эрчлээний бариулГадна эрчлээний бариул
Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Верньер штатахуун (штангенциркуль)Верньер штатахуун (штангенциркуль)
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
4

Make the push button

Make a drawn metal tube closed at the top, and a rod with a head. Put a small coil spring in the top of the tube, then the rod's head. Wedge a washer into the tube under the head. Leave clearance so the rod can swivel a little. Turn the rod's lower end down to a smaller diameter. Unknown: the metal.

Энэ алхмын материал:

Тодорхойгүй металлТодорхойгүй металл1 as required
Шахалтын пүршний иж бүрдэлШахалтын пүршний иж бүрдэл1 spring

Шаардлагатай багаж:

Металл эрэгМеталл эрэг
Токарийн багажны багц (HSS)Токарийн багажны багц (HSS)
Верньер штатахуун (штангенциркуль)Верньер штатахуун (штангенциркуль)
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
5

Assemble

Set the terminals in their recesses and the contacts in their grooves. Slide the button into the sleeve, with a coil spring round the rod between the cover and the wedged washer. Pass the rod's end through the cover's hole. Put on it a loose insulating washer with a metal rim round its edge. Hammer the rod's end over into a flange. Lay the cover on the housing, so its ears clamp the terminals, and bend the plate's tangs over the bead.

Энэ алхмын материал:

Тодорхойгүй тусгаарлагч материалТодорхойгүй тусгаарлагч материал1 as required
Тодорхойгүй металлТодорхойгүй металл1 as required
Шахалтын пүршний иж бүрдэлШахалтын пүршний иж бүрдэл1 spring

Шаардлагатай багаж:

Ширээний хавчаарШирээний хавчаар
Бөмбөрцөг толгойт алхБөмбөрцөг толгойт алх
Хавтгай хошуут хямсааХавтгай хошуут хямсаа
Хамгаалалтын нүдний шилХамгаалалтын нүдний шил
6

Mount and wire it

Put the sleeve through a hole in the panel and clamp the panel between two nuts on the thread. Solder the bared wire ends to the two lugs.

Энэ алхмын материал:

Зургаан талт эрэгЗургаан талт эрэг2 pcs
Гагнуурын утасГагнуурын утас1 as required

Шаардлагатай багаж:

Гагнуурын хэрэгсэлГагнуурын хэрэгсэл
Хавтгай хошуут хямсааХавтгай хошуут хямсаа
7

Check it

At rest, the rim sits against the underside of the cover and the circuit is open. Pressed, the rim meets the stepped ends of both contacts and closes it. The checking is ours: the meter reads open, then closed while pressed.

Шаардлагатай багаж:

МультиметрМультиметр

Материал

5

Шаардлагатай багаж

13

Энэ загвараар хийдэг

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...