Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
1/4 W Resistor Kit: Carbon Film Resistors Rated and Colour-Coded to MIL-PRF-22684 Style RL07
Ed

Зохиогч

Ed

2. Арван нэгдүгээр сар 2026FI
12
0
0
0
0

1/4 W Resistor Kit: Carbon Film Resistors Rated and Colour-Coded to MIL-PRF-22684 Style RL07

A 1/4 W rating is earned, not printed: the US military resistor specification gives its RL07 style 1/4 W at 70 °C only if the resistors survive its tests. Carbon film resistors in a range of values are checked, overloaded for 5 seconds, run for 1,000 hours at 70 °C on a sample, colour-coded with five bands and sorted into a kit. Result: an assortment of 1/4 W carbon film resistors, ±5 % or ±2 %, each band-coded with its value. Source: MIL-PRF-22684F, Resistors, Fixed, Film (Insulated) (US Department of Defense, 2006), style RL07. Not given here: the RL07 body and lead sizes and the allowed change in the life test, which are in the RL07 detail sheet. Unknown: the band paint; only its colours are fixed. Picture: Wikimedia Commons.
Дунд шат
6 weeks

Зааварчилгаа

1

Check each value

Measure the dc resistance of every resistor. It must lie within its tolerance of the nominal value: ±5 % or ±2 %. Work out its rated working voltage from E = √(P × R) with P = 1/4 W, but never above 250 V: for example 50 V for 10 kΩ, 9.1 V for 330 Ω. Ours: a Wheatstone bridge.

Энэ алхмын материал:

Нүүрстөрөгчийн хальсан резисторНүүрстөрөгчийн хальсан резистор1 assorted values, as many of each as the kit needs

Шаардлагатай багаж:

Уитстоны гүүрУитстоны гүүр
2

Overload for 5 seconds

Mount a resistor horizontally in still air, nothing within 3 in. of it except the base 2 in. below. Apply 2.5 times its rated working voltage (but not more than 500 V) for 5 seconds. Measure again 30 to 35 minutes later: the change may not exceed ±(0.5 % + 0.05 Ω), with no arcing, burning or charring.

Шаардлагатай багаж:

Шууд урсгалын тэжээлийн үүсгүүрШууд урсгалын тэжээлийн үүсгүүр
Секунд хэмжигчСекунд хэмжигч
Уитстоны гүүрУитстоны гүүр
3

Run the life test on samples

Solder sample resistors from the batch to lightweight terminals with 1 in. of lead, spaced so none warms another, in still air at 70 °C (+15, -5). Measure them first, then apply the rated working voltage 1 1/2 hours on and 1/2 hour off for 1,000 hours, measuring at the end of an off period after 250, 500 and 1,000 hours. A batch whose samples pass carries the 1/4 W rating. Not given here: the allowed change, which the RL07 detail sheet sets. Ours: an oven as the 70 °C chamber.

Шаардлагатай багаж:

ЗуухЗуух
ТермометрТермометр
Шууд урсгалын тэжээлийн үүсгүүрШууд урсгалын тэжээлийн үүсгүүр
Гагнуурын хэрэгсэлГагнуурын хэрэгсэл
Гагнуурын утасГагнуурын утас
Уитстоны гүүрУитстоны гүүр
4

Paint the colour bands

On a body of any colour but black (tan is preferred), paint five bands: first figure, second figure, multiplier (black 1, brown 10, red 100 ... blue 1,000,000; gold 0.1, silver 0.01), tolerance (gold ±5 %, red ±2 %), and a wider white band, about 1 1/2 times the others, for solderable leads. Figures: black 0, brown 1, red 2, orange 3, yellow 4, green 5, blue 6, violet 7, grey 8, white 9. So 330 Ω ±5 % is orange, orange, brown, gold, white. Unknown: the paint; the colours must be permanent and nonfading.

Энэ алхмын материал:

Өнгөт туузны тэмдэглэгээний будагӨнгөт туузны тэмдэглэгээний будаг1 set of colours

Шаардлагатай багаж:

Нарийн үзүүртэй бийрНарийн үзүүртэй бийр
5

Sort into the kit

Sort the rated, coded resistors by value into the compartments of a box, one value to a compartment.

Шаардлагатай багаж:

Тоглоомын хэсгүүд эмхлэх хайрцагТоглоомын хэсгүүд эмхлэх хайрцаг

Материал

2

Шаардлагатай багаж

9

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...