УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
НОГООН ИРЭЭДҮЙ
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Casting Reinforced Concrete — Marrying Steel and Stone into the Modern Structure
Balin

Зохиогч

Balin

25. Зургадугаар сар 2026US
0
0
0
0
0

Casting Reinforced Concrete — Marrying Steel and Stone into the Modern Structure

Concrete is wonderful stuff in compression — squeeze it and it holds — but pull on it and it cracks like a biscuit. Steel is the opposite: superb in tension, useless if you try to build a wall of it. In the late 1800s builders like Joseph Monier and François Hennebique realised that embedding steel inside concrete combines the best of both, and reinforced concrete became the material that built the modern world.

The idea works because of three lucky properties. Concrete and steel expand and contract at almost exactly the same rate, so temperature changes do not tear them apart. Wet concrete is strongly alkaline, which coats the steel in a protective film that stops it rusting. And the two grip each other firmly, so a load shared between them is truly shared. Put steel where the structure is stretched and concrete where it is squeezed, and you get a member strong in every direction.

From this came bridges, dams, tunnels, and the skeletons of skyscrapers — shapes impossible in stone or iron alone. The skill is in knowing where the steel must go and in surrounding it completely with sound, well-cured concrete.

Дунд шат
A day to pour, plus weeks to cure

Зааварчилгаа

1

Understand the partnership

Concrete is strong when squeezed but weak when stretched; steel is strong when stretched. Reinforced concrete puts steel inside concrete so that concrete carries the compression and steel carries the tension. Each does what it is good at.
2

Know where the steel goes

Work out which parts of the structure will be stretched under load and put the steel there. In a simple beam, the underside stretches, so the reinforcing bars run near the bottom; in a column, bars run the full height. Steel in the wrong place does nothing.
3

Build the formwork

Build sturdy timber formwork in the exact shape of the finished member — beam, slab, or column. It must be rigid and well braced, because wet concrete is heavy and will bulge or burst weak forms.

Materials for this step:

Timber PlankTimber Plank10 ширхэг

Tools needed:

HammerHammer
4

Cut and bend the rebar

Cut steel reinforcing bars to length and bend hooks on their ends so they anchor firmly in the concrete. Bending and hooking the bars stops them pulling out under load and ties the structure together.

Materials for this step:

Steel RebarSteel Rebar15 метр

Tools needed:

Bar BenderBar Bender
5

Place and tie the cage

Assemble the bars into a cage and set it in the formwork on small spacers so that concrete will surround every bar with a layer of cover. Tie the intersections with wire. The cover layer is vital — it protects the steel from rust and fire.

Materials for this step:

Tie WireTie Wire1 боодол
6

Mix the concrete

Mix Portland cement, clean sand, and gravel in proportions of roughly one to two to four, with just enough water to make a workable paste. Too much water weakens the concrete, so use the least that lets it flow around the bars.

Materials for this step:

Portland CementPortland Cement50 кг
SandSand100 кг
GravelGravel200 кг

Tools needed:

Concrete MixerConcrete Mixer
7

Pour around the steel

Pour the wet concrete into the formwork, filling it completely around the rebar cage. Work it into the corners and under the bars so no steel is left exposed and no large pockets are left empty.

Materials for this step:

WaterWater30 литр
8

Compact out the air

Vibrate or rod the wet concrete to drive out trapped air bubbles so it flows tight against the steel and fills the form solidly. Voids next to a bar break the bond and let water reach the steel, so thorough compaction is essential.

Tools needed:

Tamping RodTamping Rod
9

Cure it slowly

Keep the concrete damp and protected for at least a week. Concrete hardens by a slow chemical reaction with water, not by drying, so letting it dry out too fast leaves it weak and cracked. Patience here makes strong concrete.
10

Strip the formwork

Once the concrete has gained enough strength — days for slabs, longer for beams that carry load — carefully remove the formwork. Strip too early and the member can sag or crack before it is ready to bear weight.

Tools needed:

Pry BarPry Bar
11

Understand why it lasts

Three properties make the marriage durable: concrete and steel expand at nearly the same rate so heat does not split them, the alkaline concrete coats the steel and stops it rusting, and the two grip tightly so they share load. Keep the steel well covered and the concrete sound and it will last generations.
12

See what it built

Reinforced concrete made shapes impossible in stone or iron alone — long bridge spans, thin floor slabs, dams, tunnels, and the frames of tall buildings. Cheap, mouldable, and strong in every direction, it became the dominant structural material of the modern world.

Материал

7

Шаардлагатай багаж

5

Connected Blueprint Materials

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

Mixing Roman Concrete (Opus Caementicium) — Volcanic Ash Hydraulic CementEmma зохиосон

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Loading comments...