Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Profile Gauge: Sliding Pins Held by Cloth-Wrapped Rubber Tubes (Reinhardt, 1918)
Forge

Зохиогч

Forge

13. Арван нэгдүгээр сар 2026NO
7
0
0
0
0

Profile Gauge: Sliding Pins Held by Cloth-Wrapped Rubber Tubes (Reinhardt, 1918)

James H. Reinhardt of East Orange, New Jersey, received US 1,261,438, dated 2 April 1918, for a profile gauge: a row of pins clamped between two thin metal members. Rubber tubes wrapped in cloth press on the pins, so each one slides when pushed and stays where it is left. Pressed against an object, the pin ends take its outline, and a pencil drawn along them copies it, so the shape can be made again. We build his single gauge from brass sheet and steel wire. All sizes are ours.
Дунд шат
About 5 hours

Зааварчилгаа

1

How many pins

Jupyter дэвтэр ачаалж байна…
2

Read US 1,261,438

"The rods or pins 3 of the respective gages may be pushed against the surface of the object, as required, to obtain its outline along the ends of the rods or pins, whereby a pencil may be drawn along the ends of the pins to trace such outline or contour of the object. From such outlines objects corresponding to the master object may be reproduced either in relief or concave according to which way the outline drawn from the ends of the rods is used."
3

Make the two members

Cut two strips of 0.8 mm brass sheet 200 x 32 mm (ours) with tin snips and file the edges. Bend 4 mm down along each long side in the vice, so each strip becomes a shallow channel 24 mm wide: his "gutter-like form". Clamp them together, open sides facing, and drill a 3.5 mm hole through both, 50 mm from each end, on the middle line.

Энэ алхмын материал:

Гуулин хуудасГуулин хуудас2 ширхэг

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Гилбэрийн иж бүрдэлГилбэрийн иж бүрдэл
Ширээний хавчаарШирээний хавчаар
Зурмал зүүЗурмал зүү
Гар өрөмГар өрөм
4

Make the gutters

Cut two strips of the same brass 180 x 14 mm and bend each round a 6 mm rod into a U that will hold the rubber tube, his gutters 10. Rivet them inside one member, one near each long side, with copper rivets, keeping clear of the screw holes.

Энэ алхмын материал:

Гуулин хуудасГуулин хуудас1 ширхэг
Зэсэн риветЗэсэн ривет6 ширхэг

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Зөөлөн ганан дугуй баганзЗөөлөн ганан дугуй баганз
Ширээний хавчаарШирээний хавчаар
Гар өрөмГар өрөм
Бөмбөрцөг толгойт алхБөмбөрцөг толгойт алх
5

Make the retainers

Cut two pieces of 6 mm rubber tubing 170 mm long and push a 2 mm wire through each, his cores 9, "to somewhat stiffen them". Wrap each in a strip of cotton cloth, lap its edges and glue them with contact cement, his protecting cloth 12, so the rubber does not touch the metal. Lay one in each gutter.

Энэ алхмын материал:

Резинэн хоолойРезинэн хоолой1 ширхэг
Ган утасГан утас1 ширхэг
Хөвөн даавууХөвөн даавуу1 ширхэг
Холбоо цавууХолбоо цавуу1 ширхэг

Шаардлагатай багаж:

Хажуугийн утас таслагч хямсааХажуугийн утас таслагч хямсаа
ХайчХайч
6

Cut the pins

Cut 1 mm steel wire into pins 120 mm long, as many as the notebook gives. Straighten any that are bent and file both ends flat and smooth, so they slide easily and do not mark the work.

Энэ алхмын материал:

Ган утасГан утас1 ширхэг

Шаардлагатай багаж:

Хажуугийн утас таслагч хямсааХажуугийн утас таслагч хямсаа
Зүү гилбэрийн иж бүрдэлЗүү гилбэрийн иж бүрдэл
Ширээний хавчаарШирээний хавчаар
7

Assemble

Lay the member with the retainers open side up. Lay the pins across it side by side, touching, centred so equal lengths stick out on both sides; leave a gap at each screw hole (ours). Put the other member on top and pass a machine screw through each hole with a nut. Tighten them evenly until each pin slides when pushed but does not fall.

Энэ алхмын материал:

Машины шурагМашины шураг2 ширхэг
Зургаан талт эрэгЗургаан талт эрэг2 ширхэг

Шаардлагатай багаж:

Халив иж бүрдэлХалив иж бүрдэл
Тохируулгатай түлхүүрТохируулгатай түлхүүр
8

Take a profile

Push all the pins level with a flat board. Press the gauge square against the object until the pins have taken its shape. Lift it off, lay it on paper or on the stock to be cut, and draw a pencil along the pin ends.

Шаардлагатай багаж:

ХарандааХарандаа
9

Troubleshooting

Pin profile gauge troubleshooting.

Flow

Loading...
10

History and honest limits

**James H. Reinhardt** of East Orange, New Jersey, US 1,261,438, dated 2 April 1918, filed 20 June 1914. He claimed "a profile gage comprising a pair of opposed members, rods or pins located between and transversely with respect to said members, means for clamping said members together" and "a resilient retainer comprising spaced rubber tubes". His members can have teeth along their edges, and his patent also covers end castings that join several gauges in a line or at an angle, a smaller gauge clamped between them, a toothed spacer strip and a rubber-mat retainer: none of those are built here. He gives no sizes: the brass, the 200 mm length, the 1 mm pins, the tube and core sizes, the cement, the rivets and the screws are ours.

Материал

8

Шаардлагатай багаж

13

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...