Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Jack-o'-Lantern Light: a Dry Cell in a Tin Clip and a Hinged Bulb Holder Instead of a Candle (Root, 1953)
Forge

Зохиогч

Forge

13. Арван нэгдүгээр сар 2026NO
7
0
0
0
0

Jack-o'-Lantern Light: a Dry Cell in a Tin Clip and a Hinged Bulb Holder Instead of a Candle (Root, 1953)

Howard S. Root of Spokane received US 2,631,224, dated 10 March 1953, for a safe light for jack-o'-lanterns: "The most common device is an ordinary candle. That, however, is very dangerous." A springy tin clip holds a dry cell; a bulb screwed into a hinged tin support rests on the top of the cell, and the clip itself carries the current back from the bottom. A wire handle through the lid lifts the bulb to switch it off. We bend it from tinplate and fit it in a carved pumpkin. All sizes are ours.
Анхан шат
About 2 hours

Зааварчилгаа

1

Bracket blank

Jupyter дэвтэр ачаалж байна…
2

Read US 2,631,224

"I provide an operating means for the light bulb support 18 of such a nature that the child can turn the light on and off at will, yet if the entire toy is carried by the operating handle, no harm is done to the device."
3

Bend the cell clip

Cut the tinplate strip from the notebook. Bend it into a U round the cell, his container 10: the bottom is the cross bar 10c, the sides are legs 10a and 10b. Curve the legs a little across their width so the cell cannot slide out sideways, and snip and press in a small tongue on each leg (his 15) to grip it. Snip two pointed fingers at the bottom (his 13).

Энэ алхмын материал:

Цагаан тугалган хуудасЦагаан тугалган хуудас1 ширхэг

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Хавтгай хошуут хямсааХавтгай хошуут хямсаа
4

Make the bulb support

Cut a tin plate a little longer than the cell is wide, his support 18. Punch a hole in the middle just big enough for the bulb's screw base to screw into (his threaded aperture 19; ours). Bend two small ears at the top of leg 10a (his 21) and roll the support's end round a wire pin (22) between them, so it hinges.

Энэ алхмын материал:

Цагаан тугалган хуудасЦагаан тугалган хуудас1 ширхэг
Пүршний ган утасПүршний ган утас1 ширхэг

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Төвлүүлэх цүүцТөвлүүлэх цүүц
Дугуй хошуут хавчаарДугуй хошуут хавчаар
Хавтгай хошуут хямсааХавтгай хошуут хямсаа
5

Fit the spring and handle

Wind a few turns of spring wire on the hinge pin, one end hooked over the top of leg 10a and the other over the support, so it presses the support down (his spring 25). Bend a wire handle (his 20) long enough to come out of the top opening; pivot its lower end in a turned-over tab on leg 10b (26) and bend a short arm (27) under the free end of the support, so raising the handle lifts the bulb.

Энэ алхмын материал:

Пүршний ган утасПүршний ган утас1 ширхэг

Шаардлагатай багаж:

Дугуй хошуут хавчаарДугуй хошуут хавчаар
Хавтгай хошуут хямсааХавтгай хошуут хямсаа
Хажуугийн утас таслагч хямсааХажуугийн утас таслагч хямсаа
6

Put in the cell and bulb

Seat the cell with its centre terminal down on the cross bar, put a tin band (his 16) round the legs if they are loose, and screw the bulb into the support. Let the support down: the bulb's end terminal should touch the top of the cell and light, the current returning through the support, the hinge and the clip.

Энэ алхмын материал:

Хуурай элементХуурай элемент1 ширхэг
Гар чийдэнгийн гэрлийн шилГар чийдэнгийн гэрлийн шил1 ширхэг
Цагаан тугалган хуудасЦагаан тугалган хуудас1 ширхэг

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Хавтгай хошуут хямсааХавтгай хошуут хямсаа
7

Fit it in the pumpkin

Carve the pumpkin's face and cut the top opening (ours; his toys are hollow figures). Push the clip's fingers through the bottom of the pumpkin, put a washer over them outside, and bend them over it (his washer 8), so the light stands in the middle. Pass the handle up through the top opening.

Энэ алхмын материал:

ХулууХулуу1 ширхэг
Хавтгай угаагуурХавтгай угаагуур1 ширхэг

Шаардлагатай багаж:

Гар урлалын хутгаГар урлалын хутга
Хавтгай хошуут хямсааХавтгай хошуут хямсаа
8

Use it

Lower the handle and the bulb lights; raise it and the light goes off. To change the cell, lift the support and take the cell out.
9

Troubleshooting

Jack-o'-lantern light troubleshooting.

Flow

Loading...
10

History and honest limits

**Howard S. Root** of Spokane, Washington, US 2,631,224, dated 10 March 1953, filed 21 December 1948. He claimed "an illuminated figure toy comprising a hollow body having an opening in the top thereof", a conductive container for a dry cell, a hinged conductive bulb support, and spring means pressing the bulb's end terminal against the cell. He also shows other hinges, a magnet latch and a side handle (Figs. 6-13), not built here. He gives no sizes or materials: the tinplate, all sizes, the pumpkin and the cell and bulb are ours.

Материал

6

Шаардлагатай багаж

6

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...