Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Saw File: Three-Square, Forged in a Boss, Cut by Hand and Hardened (Ure, 1839)
Forge

Зохиогч

Forge

4. Арван нэгдүгээр сар 2026NO
22
0
0
0
0

Saw File: Three-Square, Forged in a Boss, Cut by Hand and Hardened (Ure, 1839)

The file for sharpening saw teeth as Sheffield made it by hand: a three-square (triangular) bar of cast steel, not tapering, forged in a V-shaped boss, its teeth cut one by one with a chisel and hammer, then hardened under a coat of animal carbon and salt and quenched in cold spring water. Ure says saw files in particular should be hardened with the carbon mixture, so they will cut iron and steel. Not given: sizes and teeth per inch. Source: A. Ure, Dictionary of Arts, Manufactures, and Mines (1839), File. Picture: our drawing.
Дээд шат
Unknown

Зааварчилгаа

1

Forge the blank

Draw cast steel out square at the forge, then lay it with one angle down in a boss whose recess has two sides meeting at an angle, so the hammer forms one side and the boss the other two. Keep it the same size along its length (saw files are not tapered).

Энэ алхмын материал:

Тигелийн ганТигелийн ган1 cast steel bar
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс1 ширхэг

Шаардлагатай багаж:

Дархны зуухДархны зуух
Дархны хямсааДархны хямсаа
Доод хэвлэгч (хэв)Доод хэвлэгч (хэв)
АлхАлх
Том алхТом алх
2

Cut the teeth

On an anvil with a flat, even face, hold the file down with a leather strap over each end, the workman's feet in the straps like stirrups. Cut the teeth with a chisel a little broader than the file, sharpened to about 20 degrees, struck with a hammer of 1 to 6 lb. For single cut, run a fine file lightly over the teeth to take off the roughness; for double cut, cut a second set nearly at right angles to the first.

Шаардлагатай багаж:

Ган дөшГан дөш
Арьсан оосорАрьсан оосор
Хүйтэн цүүцХүйтэн цүүц
АлхАлх
Металлын гилбэрМеталлын гилбэр
3

Cut the other sides

To cut the next side, lay the file in a piece of lead-tin alloy with an angular groove, so the teeth already cut are not spoiled on the anvil.

Шаардлагатай багаж:

Цагаан тугалга-хар тугалганы гагнуурЦагаан тугалга-хар тугалганы гагнуур
Ган дөшГан дөш
Хүйтэн цүүцХүйтэн цүүц
АлхАлх
4

Coat for hardening

Distil shoemakers' and curriers' leather refuse in an iron still and powder the bright coal left. Grind about equal parts by bulk of this carbon and salt to the consistence of cream with water and cover the file with it.

Шаардлагатай багаж:

Төмөр нэрэх савТөмөр нэрэх сав
ДавсДавс
УсУс
5

Harden

Hold the file by the tang in a fire of very small cokes, drawing it out often, until it is an even cherry red from tang to point. Plunge it straight down, quickly, into clear spring water as cold as possible.

Шаардлагатай багаж:

Дархны зуухДархны зуух
Металлургийн коксМеталлургийн кокс
Дархны хямсааДархны хямсаа
УсУс
6

Clean and oil

Brush the file with water and powdered cokes until clean and metallic, wash it in two or three waters to take off all the salt, dip it in lime-water, dry it quickly before the fire and oil it while warm with olive oil containing a little oil of turpentine.

Шаардлагатай багаж:

Металлургийн коксМеталлургийн кокс
УсУс
Шохойн усШохойн ус
Чидун жимсний тосЧидун жимсний тос
СкипидарСкипидар

Материал

2

Шаардлагатай багаж

17

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...