Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Screwdriver: a Flat Blade Forged, Packed at a Low Heat and Tempered Grey (Holford, 1907)
Forge

Зохиогч

Forge

4. Арван нэгдүгээр сар 2026NO
10
0
0
0
0

Screwdriver: a Flat Blade Forged, Packed at a Low Heat and Tempered Grey (Holford, 1907)

A flat screwdriver is a steel shank flattened to a blade that fits the slot of a screw. H. Holford's 20th Century Toolsmith and Steelworker (1907) says most smiths make them so they twist or break on a hard screw, and gives his cure: forge it from 75-point carbon steel, strike the blade a few good blows on each flat at a low heat, harden it and let the temper run to grey. His Fig. 60 shows the shape without its handle. He gives no sizes and no handle, which are unknown here; the brine bath is from his chapter on the hardening bath. Source: H. Holford (1907), pp. 21, 118. Picture: his Fig. 60.
Дунд шат
Half a day

Зааварчилгаа

1

Read Holford

"Strike it a few good blows on each flat side of the screw driving edge while at a low heat. Then harden and allow the temper to draw to a grey, cool off and you will have a screw driver that will give unlimited satisfaction."
2

Forge the shape

Take good steel of 75 points carbon. Forge it to the shape of Fig. 60: a round shank, flattened at one end to the driving blade and drawn to a pointed tang at the other for the handle. Holford gives no sizes (unknown).

Энэ алхмын материал:

Дөрвөлжин багажийн ган савааДөрвөлжин багажийн ган саваа1 bar

Шаардлагатай багаж:

Дархны зуухДархны зуух
ДөшДөш
Дархны алхДархны алх
Дархны хавчаарДархны хавчаар
Тодорхойгүй хэмжээсТодорхойгүй хэмжээс
Хамгаалалтын нүдний шилХамгаалалтын нүдний шил
Халуунд тэсвэртэй бээлийХалуунд тэсвэртэй бээлий
3

Pack the blade

At a low heat, strike a few good blows on each flat side of the driving edge.

Шаардлагатай багаж:

Дархны алхДархны алх
ДөшДөш
Дархны зуухДархны зуух
Дархны хавчаарДархны хавчаар
4

Harden and temper grey

Heat the blade end evenly and quench it in the hardening bath. Holford's bath is clean water free from grease, best made into a brine with as much salt as the water will dissolve, kept as large and as cold as possible. Brighten the blade with a file so the colours show, draw the temper to a grey, then cool it off.

Шаардлагатай багаж:

Дархны зуухДархны зуух
Ханасан давсны уусмалХанасан давсны уусмал
Дархны хавчаарДархны хавчаар
Нарийн гилбэрНарийн гилбэр
Халуунд тэсвэртэй бээлийХалуунд тэсвэртэй бээлий
5

Fit a handle

Fit a handle on the tang. Holford shows the screwdriver without one and does not say what it is made of (unknown).

Энэ алхмын материал:

Тодорхойгүй материалТодорхойгүй материал1 handle
6

History and honest limits

Holford, a toolsmith writing for blacksmiths and tool dressers, says a good screwdriver is prized by every mechanic, woodworkers most of all, yet few smiths could make one that would not break or twist. His temper table lists the screwdriver at grey, in 0.75 carbon steel. He gives no sizes, no handle and no heat for hardening; those are unknown here, and the tools are ours.

Материал

2

Шаардлагатай багаж

9

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...