УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
НОГООН ИРЭЭДҮЙ
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Reading a Photoresistor — SIK Circuit 6
Ed

Зохиогч

Ed

17. Гуравдугаар сар 2026FI
73
0
0
0
0

Reading a Photoresistor — SIK Circuit 6

Use a photoresistor (light sensor) to control LED brightness. Learn about voltage dividers, analog input, and the map() function for sensor-to-output conversion.

Зааварчилгаа

1

Parts & Introduction

A photoresistor (or LDR — Light Dependent Resistor) changes resistance based on light levels. Combined with a fixed resistor, it forms a voltage divider that the Arduino can read as an analog value. You'll use this to control LED brightness automatically.

Parts Needed

  • 1x Arduino Uno + USB cable
  • 1x Breadboard
  • 1x Photoresistor
  • 1x LED (any color)
  • 1x 330Ω Resistor
  • 1x 10KΩ Resistor (for voltage divider)
  • 6x Jumper Wires

Materials for this step:

SparkFun Inventors Kit - V3.2SparkFun Inventors Kit - V3.21 багц
Arduino Uno R3Arduino Uno R31 ширхэг
BreadboardBreadboard1 ширхэг
PhotoresistorPhotoresistor1 ширхэг
5mm LED5mm LED1 ширхэг
330 Ohm Resistor330 Ohm Resistor1 ширхэг
10K Ohm Resistor10K Ohm Resistor1 ширхэг
Jumper WiresJumper Wires5 ширхэг

Tools needed:

Computer with Arduino IDE
2

Hardware Hookup

Wiring Instructions

  1. Connect one side of the photoresistor to 5V.
  2. Connect the other side to Analog Pin A0.
  3. Connect a 10K resistor from Analog Pin A0 to GND (this completes the voltage divider).
  4. Connect the LED positive leg to Digital Pin 9 (PWM-capable).
  5. Connect the LED negative leg through a 330Ω resistor to GND.

The voltage divider produces a voltage proportional to light level, which the Arduino reads as 0-1023.

Materials for this step:

PhotoresistorPhotoresistor1 ширхэг
5mm LED5mm LED1 ширхэг
330 Ohm Resistor330 Ohm Resistor1 ширхэг
10K Ohm Resistor10K Ohm Resistor1 ширхэг
BreadboardBreadboard1 ширхэг
Jumper WiresJumper Wires5 ширхэг
3

Arduino Code

Open the Arduino IDE and upload the following sketch to your Arduino board.

photoresistor.inoarduino
/*
SparkFun Inventor's Kit
Example sketch 06 — PHOTORESISTOR

Use a photoresistor (light sensor) to control LED brightness.

Hardware connections:
  Photoresistor: one side to 5V, other side to analog pin 0
  10K resistor between analog pin 0 and GND
  LED: positive to digital pin 9 (PWM), negative through 330 ohm to GND

This code is completely free for any use.
*/

const int sensorPin = 0;
const int ledPin = 9;

int lightLevel, high = 0, low = 1023;

void setup()
{
  pinMode(ledPin, OUTPUT);
}

void loop()
{
  lightLevel = analogRead(sensorPin);

  manualTune();

  //autoTune();

  analogWrite(ledPin, lightLevel);
}

void manualTune()
{
  lightLevel = map(lightLevel, 0, 1023, 0, 255);
  lightLevel = constrain(lightLevel, 0, 255);
}

void autoTune()
{
  if (lightLevel < low)
  {
    low = lightLevel;
  }
  if (lightLevel > high)
  {
    high = lightLevel;
  }

  lightLevel = map(lightLevel, low+30, high-30, 0, 255);
  lightLevel = constrain(lightLevel, 0, 255);
}

Materials for this step:

Arduino Uno R3Arduino Uno R31 ширхэг

Tools needed:

Computer with Arduino IDE
4

Test & Experiment

What You Should See

The LED brightness changes based on ambient light. Cover the photoresistor to dim or brighten the LED (depending on orientation).

Troubleshooting

  • LED stays dark: Check LED polarity. Also verify the photoresistor is in the circuit correctly.
  • Not responding to light: The photoresistor spacing is non-standard — make sure both legs are making good contact.
  • Subtle changes: Try using a flashlight or covering the sensor completely for more dramatic results.

Experiments to Try

  • Uncomment autoTune() to let the Arduino automatically calibrate to your lighting conditions.
  • Use the sensor to trigger actions at specific light thresholds (e.g., turn on a "night light" when dark).

Материал

8

Шаардлагатай багаж

1
  • 13
    Computer with Arduino IDE
Estimated Total
$141.00

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Loading comments...