Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ

Spanner Set: Open-End Wrenches for 1/4 to 1 Inch Bolts (Machinery's Handbook, 1924)
A set of open-end spanners made to the standard dimensions in Machinery's Handbook. The jaw opening fits the nut of each bolt size, and head width, head thickness and length grow with it, so each spanner is strong enough for its own nut.
Variable: the bolt size. The table gives each spanner's dimensions from 1/4 in up to 3 1/2 in bolts; this set covers 1/4 to 1 in.
Source: Machinery's Handbook (1924), p. 848, Dimensions of Wrenches. Unknown: the steel and its hardening. Picture: the Handbook's page.
Дунд шат
Unknown
Зааварчилгаа
1
1
Pick the sizes
Pick the sizes
For each bolt size, the Handbook gives jaw opening A, head width B, head thickness H and overall length L, in inches. 1/4 in bolt: 1/2, 1, 1/4, 5 1/2. 5/16: 19/32, 1 3/16, 5/16, 6. 3/8: 11/16, 1 3/8, 3/8, 7. 7/16: 25/32, 1 9/16, 7/16, 8. 1/2: 7/8, 1 3/4, 1/2, 9. 9/16: 31/32, 1 15/16, 9/16, 10. 5/8: 1 1/16, 2 1/8, 5/8, 11. 3/4: 1 1/4, 2 1/2, 11/16, 12 1/2. 7/8: 1 7/16, 2 15/16, 3/4, 14 1/2. 1 in: 1 5/8, 3 5/16, 7/8, 16 1/2. The neck and handle sizes are in the same table. Ours: a set of these ten.
Шаардлагатай багаж:
Микрометр2
2
Forge the blanks
Forge the blanks
Forge each spanner from bar: a round head as wide as B and as thick as H, a neck, and a handle to make the overall length L. Ours: carbon steel bar forged under a power hammer. Not given: the steel, the forging method.
Энэ алхмын материал:
Нүүрстөрөгчит ган саваа (0.6 % C)10 ten spannersШаардлагатай багаж:
Дархны зуух
Машин алх
Дөш3
3
Cut the jaws and harden
Cut the jaws and harden
Cut the open jaw in each head to the opening A, so it fits across the flats of that bolt's nut, and finish the faces parallel. Check each opening. Harden and temper the spanners. Not given: the hardening.
Шаардлагатай багаж:
Фрезийн машин
Металлын гилбэр
Микрометр
Дулааны боловсруулалтын зуух
Хатууруулах тэвшМатериал
1- 10 ten spannersТүр орлуулагч
Энэ загвараар хийдэг
CC0 Нийтийн домэйн
Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.
Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.
