Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
55-Gallon Open-Head Steel Drum to ICC Specification 17H (1964)
Youblob · CC0
Forge

Зохиогч

Forge

27. Аравдугаар сар 2026NO
18
0
0
0
0

55-Gallon Open-Head Steel Drum to ICC Specification 17H (1964)

The open-top 55-gallon (208-litre) steel drum, built to the rule US railways and shippers used for single-trip removable-head drums: welded low-carbon steel body, three rolled hoops, a crowned bottom, and a lid clamped by a bolted ring over a gasket. Source: ICC Specification 17H, 49 CFR 78.118, Federal Register, 29 December 1964. The spec does not say how the bottom is joined. The litre figure, the gasket rubber and the machines are ours. Picture drawn by Youblob.
Дээд шат
Production line

Зааварчилгаа

1

Cut low-carbon steel sheets

Use low-carbon steel for body and heads. For a 55-gallon drum: body 18 gauge, bottom head 18 gauge, removable head 14 gauge (16 gauge if the cover has one or more corrugations near its edge). 18 gauge is 0.0478 in nominal and at least 0.0428 in; 14 gauge 0.0747 in and at least 0.0677 in, measured at least 3/8 in from an edge.

Энэ алхмын материал:

Зөөлөн ган хуудасЗөөлөн ган хуудас1 body, bottom and lid sheets

Шаардлагатай багаж:

Хүнд даацын металл хайчХүнд даацын металл хайч
МикрометрМикрометр
2

Roll and weld the body

Roll the body sheet into a cylinder and weld the seam. The body seam must be welded.

Шаардлагатай багаж:

Хуудас нугалах галзууХуудас нугалах галзуу
Хоолойн оёдол гагнагчХоолойн оёдол гагнагч
3

Roll in three hoops

Roll or swage three hoops into the body, one of them near the top curl.

Шаардлагатай багаж:

Ирмэг товойлгох галзууИрмэг товойлгох галзуу
4

Press crowned heads

Press the bottom head crowned (convex) by at least 3/8 in, not standing out beyond the level of the chime, and fit it to the body. The spec does not say how the bottom is joined.

Шаардлагатай багаж:

Штамплах шахуургаШтамплах шахуурга
5

Make the bolted ring and gasket

Make the closing ring from 12-gauge steel with drop-forged lugs, one of them threaded, and a 5/8 in bolt and nut (for drums over 30 gallons). Fit a gasket under the lid: gaskets are required.

Энэ алхмын материал:

Зөөлөн ган хуудасЗөөлөн ган хуудас1 12-gauge strip for the ring
Зөөлөн ган дугуй савааЗөөлөн ган дугуй саваа1 for the lugs
Зургаан талт болтны цуглуулгаЗургаан талт болтны цуглуулга1 5/8 in bolt
Зургаан талт эрэгЗургаан талт эрэг1 5/8 in
Резинэн хавтанРезинэн хавтан1 gasket

Шаардлагатай багаж:

Хуудас нугалах галзууХуудас нугалах галзуу
Хэвтэй унадаг алхХэвтэй унадаг алх
Гар урлалын хутгаГар урлалын хутга
6

Check capacity and mark

The drum must hold at least 4 % more than its marked 55 gallons, and no more than 5 % more (or 4 % plus 1 quart, whichever is greater). Emboss the marks: ICC-17H, STC (single-trip container), the maker, and the gauges, capacity and year.

Шаардлагатай багаж:

Штамплах шахуургаШтамплах шахуурга
7

Leak-test every drum

Test each drum by air pressure inside of at least 7 psi with its seams under water or covered with soapsuds or heavy oil. Reject leakers, or repair them the way they were made and test again.

Энэ алхмын материал:

УсУс1 as required

Шаардлагатай багаж:

Агаар шахагчАгаар шахагч
Даралтын хэмжүүрДаралтын хэмжүүр
8

Type tests every four months

On drums taken at random and closed as for use: drop one filled with water to 98 % from 4 ft onto concrete so it lands diagonally on the chime, and hold another at 15 psi water pressure for 5 minutes. None may leak.

Энэ алхмын материал:

УсУс1 as required

Шаардлагатай багаж:

Даралтын хэмжүүрДаралтын хэмжүүр

Материал

6

Шаардлагатай багаж

10

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...