УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ

Stick Shuttle Cut from a Beech Strip
The shuttle carries the weft yarn through the shed of the loom. The simplest is the stick shuttle: a flat, narrow piece of hard wood with notches at the ends to hold the wound weft. Saw a thin beech strip a little longer than the cloth is wide, cut forked notches at both ends, round every edge and polish it smooth so it slides.
The picture: two stick shuttles wound with yarn.
Анхан шат
An afternoon
Зааварчилгаа
1
1
Cut the strip
Cut the strip
Saw and plane a straight-grained beech strip about 6 mm thick and 4 cm wide, a little longer than the cloth is wide (step 5).
Энэ алхмын материал:
Шаргалжин модон материал1 ширхэгШаардлагатай багаж:
Гар хөрөө
Гар цүүц (модны хусуур)
Шугам2
2
Cut the notches
Cut the notches
Drill a hole near each end and saw from the end into it, making a forked notch that holds the yarn. Cut a shallow long slot in the middle if you like, to make the shuttle lighter.
Шаардлагатай багаж:
Гар өрөм
Муруй хөрөө3
3
Round and smooth
Round and smooth
Round all the edges and points with the knife and rasp so nothing can catch the warp, then sand it smooth.
Шаардлагатай багаж:
Слойд хутга
Модны бүдүүн зүлгүүр
Элсэн цаас4
4
Wax it
Wax it
Rub in beeswax and polish so the shuttle slides through the shed.
Энэ алхмын материал:
Зөгийн лав0.01 кгШаардлагатай багаж:
Элсэн цаас5
5
Shuttle length for the cloth
Shuttle length for the cloth
Jupyter дэвтэр ачаалж байна…
Материал
2- 1 ширхэгТүр орлуулагч
- 0.01 кгТүр орлуулагч
Энэ загвараар хийдэг
Холбоотой загварууд
Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим
CC0 Нийтийн домэйн
Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.
Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

