УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles
Woody

Зохиогч

Woody

6. Аравдугаар сар 2026NO
28
0
0
0
0

The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles

Water dribbled onto the back of a brush stays in the bristles and never reaches the surface being washed. Frank L. Brinn of Milwaukee received US 840,604, patented 8 January 1907, for a fountain brush in which "the fluid may be delivered to the longitudinal central portion of the brush in a sheet, which when the fluid is turned on at full head will serve to separate the bristles and flush the surface to be washed": slots through the block narrow toward the bristles, fed from a cylinder on top through a tubular handle, with a cup on the handle to catch what runs down. This rung works out how the taper speeds the sheet, then cuts the slots in a scrub brush, plumbs it and compares full flow with throttled flow.
Дунд шат
About 4 hours

Зааварчилгаа

1

Sheet speed from the slot

Jupyter дэвтэр ачаалж байна…
2

Water through a brush's back before it

The embedded blueprint jets or soaks water through openings in a brush's back. Brinn shapes the openings into tapered slots so the water leaves as a sheet.
3

Read US 840,604

"By opening the valve at 3 to its full capacity a sheet of water will be discharged which will separate the bristles and effectively flush the surface to be washed, whether the bristles are in contact with such surface or not. By partially closing the valve at 3 the sheets of water escaping through the openings 18 are broken up by the bristles, and the water thus becomes distributed throughout the brush."
4

Cut the slots

On the scrub brush's top mark two slots 60 × 8 mm, 90 mm apart on the centre line. Drill a row of holes in each and cut it through with the coping saw.

Энэ алхмын материал:

Угаалгын сойзУгаалгын сойз1 ширхэг

Шаардлагатай багаж:

Ширээний хавчаарШирээний хавчаар
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Муруй хөрөөМуруй хөрөө
Арилдаггүй маркерАрилдаггүй маркер
ШугамШугам
5

Taper the slots

Pare each slot with chisels so its long sides close to about 1.5 mm at the bristle face and its ends open out to 70 mm. Trim the bristles along the slot line.

Шаардлагатай багаж:

Модны цүүцний багцМодны цүүцний багц
АлхАлх
Дижитал штангенциркуль 6 инчДижитал штангенциркуль 6 инч
Гар урлалын хутгаГар урлалын хутга
6

Make the manifold

Cut 160 mm of 22 mm copper tube and cap both ends with fittings. File a 4 mm slot along its underside over both brush slots. Fit a tee in its middle for the handle.

Энэ алхмын материал:

Зэс хоолойЗэс хоолой1 ширхэг
Гуулин холбоосГуулин холбоос1 ширхэг

Шаардлагатай багаж:

Хоолой огтлогчХоолой огтлогч
Дүрд (гар дүрд)Дүрд (гар дүрд)
Тохируулгатай түлхүүрТохируулгатай түлхүүр
7

Seat the manifold

Bed the manifold on the brush in silicone over a rubber gasket and strap it down with an aluminium strip and four wood screws.

Энэ алхмын материал:

Силиконон битүүлэгчСиликонон битүүлэгч1 ширхэг
Резинэн хавтанРезинэн хавтан1 ширхэг
Хөнгөн цагаан хуудасХөнгөн цагаан хуудас1 ширхэг
#8 × 1" модны шураг#8 × 1" модны шураг1 ширхэг

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Халив иж бүрдэлХалив иж бүрдэл
Гар урлалын хутгаГар урлалын хутга
8

Handle, valve and drip cup

Fit 1.2 m of 15 mm copper tube to the tee, with a ball valve and hose connector at its top. Slide a small tin can, holed and sealed with silicone, onto the handle as a drip cup, and fit a short copper spout low on its side.

Энэ алхмын материал:

Зэс хоолойЗэс хоолой1 ширхэг
Бөмбөлөгт хаалтБөмбөлөгт хаалт1 ширхэг
Гуулин холбоосГуулин холбоос1 ширхэг
PTFE нээлтийн битүүмжлэх туузPTFE нээлтийн битүүмжлэх тууз1 ширхэг
Цагаан тугалган савЦагаан тугалган сав1 ширхэг
Силиконон битүүлэгчСиликонон битүүлэгч1 ширхэг

Шаардлагатай багаж:

Хоолой огтлогчХоолой огтлогч
Тохируулгатай түлхүүрТохируулгатай түлхүүр
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
9

The patent drawing

US 840,604 drawing sheet, public domain (expired patent).
Алхам 9 - Image 1
10

Full flow against throttled

Connect the garden hose. With the valve fully open, hold the brush 2 cm off a board and watch the sheet part the bristles; then close it half and watch the water spread through them. Time a litre into the jug each way.
Алхам 10 - Image 1

Энэ алхмын материал:

УсУс1 ширхэг

Шаардлагатай багаж:

Хэмжих аягаХэмжих аяга
Секунд хэмжигчСекунд хэмжигч
ШугамШугам
Цэцэрлэгийн хоолойЦэцэрлэгийн хоолой
11

A sheet that sprays, sputters or leaks

Sheet-of-water fountain brush troubleshooting.

Flow

Loading...
12

History and honest limits

**Frank L. Brinn**, a citizen of Canada residing in Milwaukee, filed US 840,604 on 20 February 1905; it was patented 8 January 1907. His cylinder is held to the block by a plate with packing and screws, its slots feeding the slot-apertures; the handle's end carries a rubber sheath and the valve; the cup, with its spout, collects the water instead of letting it run down the handle when the brush is raised. **Honest limits.** A slotted copper tube stands in for his cylinder, and a tin can for his cup. The notebook treats the sheet as uniform. What you see on the board is the result.

Материал

11

Шаардлагатай багаж

18

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...