УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
The Tank-Headed Self-Feeding Brush: Soap in the Tank, a Plate to Meter It
Martin

Зохиогч

Martin

6. Аравдугаар сар 2026NO
36
0
0
0
0

The Tank-Headed Self-Feeding Brush: Soap in the Tank, a Plate to Meter It

Scrubbing a floor means going back to the bucket every few strokes. Ernest N. Broderick of Indianapolis received US 639,348, dated 19 December 1899, for a cleaning brush with a small tank on its perforated top, fed through a hollow handle from a hose; a perforated plate slid by a screw sets how far the holes open, and soap in the tank turns the water to suds — "a self-feeding brush." This rung works out how the sliding plate opens the holes, then builds the tank on a scrub brush and measures the flow at each plate setting.
Дунд шат
About 4 hours

Зааварчилгаа

1

Open area of the plate

Jupyter дэвтэр ачаалж байна…
2

A scrubbing brush before it

The embedded blueprint holds two brush heads on a sprung holder. Broderick puts a water tank on the head and feeds it through the handle.
3

Read US 639,348

"When used for scrubbing, the hose can be connected to a hydrant, and thus supply the desired amount of water to the brush, making it unnecessary to dip the brush into the bucket or tub of water. In other words, my device is a self-feeding brush. Should I desire to use soapy water, I can insert through the openings 10 particles of soap or soap powder. In this way I get soapsuds, which I use in scrubbing as it is needed, keeping the brush constantly supplied."
4

Perforate the brush back

Drill fourteen 4 mm holes through the scrub brush's back between the tufts, in two rows 30 mm apart.

Энэ алхмын материал:

Угаалгын сойзУгаалгын сойз1 ширхэг

Шаардлагатай багаж:

Ширээний хавчаарШирээний хавчаар
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Арилдаггүй маркерАрилдаггүй маркер
ШугамШугам
Тунгалаг хамгаалалтын нүдний шилТунгалаг хамгаалалтын нүдний шил
5

Make the sliding plate

Cut an aluminium plate 10 mm shorter than the back. Drill it through the back's holes, then file its end square. Rivet two guide strips to the back's top so it slides lengthwise.

Энэ алхмын материал:

Хөнгөн цагаан хуудасХөнгөн цагаан хуудас1 ширхэг
Ган риветГан ривет1 ширхэг

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Дүрд (гар дүрд)Дүрд (гар дүрд)
Риветийн багцРиветийн багц
Ривет алхРивет алх
6

Build the tank

Fold an aluminium box 50 mm deep to the back's size with a lid. Drill the lid for a 25 mm filling hole and a handle socket. Seal it to the back with silicone and screws.

Энэ алхмын материал:

Хөнгөн цагаан хуудасХөнгөн цагаан хуудас1 ширхэг
Ган риветГан ривет1 ширхэг
Силиконон битүүлэгчСиликонон битүүлэгч1 ширхэг
#8 × 1" модны шураг#8 × 1" модны шураг1 ширхэг

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Ширээний хавчаарШирээний хавчаар
Риветийн багцРиветийн багц
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Арьсан ажлын бээлийАрьсан ажлын бээлий
7

Fit the adjusting screw

Run an M4 screw through a nut epoxied on the tank's end wall so its tip pushes the plate. Turn it to close or open the holes.

Энэ алхмын материал:

Машины шурагМашины шураг1 ширхэг
Зургаан талт эрэгЗургаан талт эрэг1 ширхэг
Хоёр бүрэлдэхүүнт эпоксиХоёр бүрэлдэхүүнт эпокси1 ширхэг

Шаардлагатай багаж:

Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Халив иж бүрдэлХалив иж бүрдэл
8

Fit the handle

Fix 1.2 m of 15 mm copper tube in the socket with brass fittings. Fit a ball valve and hose connector at its top.

Энэ алхмын материал:

Зэс хоолойЗэс хоолой1 ширхэг
Гуулин холбоосГуулин холбоос1 ширхэг
Бөмбөлөгт хаалтБөмбөлөгт хаалт1 ширхэг
PTFE нээлтийн битүүмжлэх туузPTFE нээлтийн битүүмжлэх тууз1 ширхэг

Шаардлагатай багаж:

Хоолой огтлогчХоолой огтлогч
Тохируулгатай түлхүүрТохируулгатай түлхүүр
9

The patent drawing

US 639,348 drawing sheet, public domain (expired patent).
Алхам 9 - Image 1
10

Measure the flow at each setting

Connect the garden hose. Set the plate fully open, half and nearly shut, and catch the water for 30 s each in the jug. Then add a squirt of soap through the filling hole and scrub.
Алхам 10 - Image 1

Энэ алхмын материал:

УсУс1 ширхэг
Кастилийн саван (шингэн)Кастилийн саван (шингэн)1 ширхэг

Шаардлагатай багаж:

Хэмжих аягаХэмжих аяга
Секунд хэмжигчСекунд хэмжигч
Дижитал штангенциркуль 6 инчДижитал штангенциркуль 6 инч
Цэцэрлэгийн хоолойЦэцэрлэгийн хоолой
11

A brush that floods, starves or leaks

Tank-headed self-feeding brush troubleshooting.

Flow

Loading...
12

History and honest limits

**Ernest N. Broderick** of Indianapolis filed US 639,348 on 6 February 1899; it is dated 19 December 1899. Rubber or leather strips seal the tank to the brush-top. Two hollow adjustable joints, ground to fit and clamped by a bolt, let the handle be set at any angle, for floors, walls, windows or dusting high furniture; with compressed air instead of water it blows dust away, and a mop or duster may replace the brush. **Honest limits.** Our handle is fixed; his joints are not built here. The notebook gives open area, not flow through a real hole. Your flows are the result.

Материал

14

Шаардлагатай багаж

18

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...