Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Washing Machine with Churn: One Crank Pounds the Wash, Turns the Tub and Works a Dash Churn (Wagoner & Severson, 1859)
YourGrandma

Зохиогч

YourGrandma

11. Арван нэгдүгээр сар 2026IS
6
0
0
0
0

Washing Machine with Churn: One Crank Pounds the Wash, Turns the Tub and Works a Dash Churn (Wagoner & Severson, 1859)

John Wagoner and Abram Severson Jr. of Guilderland Center, New York, received US 25,152, dated 16 August 1859, for a washing machine. A crank shaft with a heavy balance wheel rocks a long lever. A springy beam on the lever carries a pounder into the tub, and a belt and a pair of bevel wheels turn the tub slowly under it. The tub stands on a hinged platform: folded up it slackens the belt, and let down the tub's weight tightens it. A pin on the lever also works the dash of a churn standing beside the machine, with or without the washing. The patent gives no sizes; every size here is ours.
Дээд шат
About 5 days, plus printing

Зааварчилгаа

1

Crank pin, strokes and tub speed

Jupyter дэвтэр ачаалж байна…
2

One crank working a churn and a washtub, a year before

Swan's machine lifted a plunger by a cam. Here a springy beam carries the pounder, and the tub's own weight tightens the belt that turns it.
3

Read US 25,152

"In addition to what has now been described our machine is adapted to operate a churn very effectively either alone or simultaneously with the washing operation." "We place the center of our tube J out of the plane of the motion of the levers T and V. Our pounder therefore inclines to strike on one side of J and not in the center thereby increasing the uniformity of the effect on the contents."
4

Print the pulley for shaft D

Flat-faced pulley 120 mm across and 40 mm wide, bored 31 mm for shaft D. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Дизайны файлSTLCC0 - Free
5

Print pulley R

Flat-faced pulley 100 mm across and 40 mm wide, bored 21 mm for the lower bevel wheel's shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Дизайны файлSTLCC0 - Free
6

Frame A, legs B and uprights C

From 70 x 70 mm timber cut three stringers 1500 mm, two cross pieces 630 mm, four legs 700 mm, an upright 830 mm and an upright 720 mm. Bolt the cross pieces across the tops of the legs and the stringers on the cross pieces, 210 mm apart, so the frame's top is 840 mm from the floor. Bolt the long upright to the outside of the front stringer 100 mm from the left end and the short one 100 mm from the right end. Chisel an opening 50 x 260 mm through the left upright, from 440 to 700 mm above the stringer, and bore it across 560 mm up for pin v (a 16 mm bolt).

Энэ алхмын материал:

Зөөлөн мод 70x70 ммЗөөлөн мод 70x70 мм11 m
Дугуй толгойт боолтДугуй толгойт боолт16 ширхэг
Хавтгай угаагуурХавтгай угаагуур16 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка16 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Хүрзэн өрмийн үзүүрийн багцХүрзэн өрмийн үзүүрийн багц
Ховилын цүүцХовилын цүүц
Модон алхМодон алх
Өнцөг шалгуурӨнцөг шалгуур
Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
Тохируулгатай түлхүүрТохируулгатай түлхүүр
Савааны хавчаарСавааны хавчаар
7

Shaft D, balance wheel F and crank E

Bolt three bearing blocks on the stringers' tops 650 mm from the left end and pass a 30 mm steel shaft D through them, 710 mm long. Build the balance wheel from three layers of 20 mm hardwood segments glued crossways: 840 mm across, a 100 mm rim and four spokes, 50 mm thick in all. Fit it on D between the front and middle stringers, the printed pulley between the middle and back stringers, and a hand crank 240 mm long on the back end. On the front end fit crank E, a hardwood arm 20 mm thick with a slot from 50 to 125 mm out, and a 20 mm bolt in the slot for the crank pin e.

Энэ алхмын материал:

Зэвэрдэггүй ган савааЗэвэрдэггүй ган саваа1 ширхэг
Холхивчийн суурьХолхивчийн суурь3 ширхэг
Хатуу модон банзХатуу модон банз3 ширхэг
Модны цавууМодны цавуу1 ширхэг
Зургаан талт болтны цуглуулгаЗургаан талт болтны цуглуулга13 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка13 ширхэг
Shaft CollarShaft Collar2 ширхэг

Шаардлагатай багаж:

Хөрөө (лобзик)Хөрөө (лобзик)
Луужин (компас)Луужин (компас)
Ширээний хөрөөШирээний хөрөө
Утасгүй өрөмУтасгүй өрөм
Хүрзэн өрмийн үзүүрийн багцХүрзэн өрмийн үзүүрийн багц
Гар фрезерГар фрезер
Савааны хавчаарСавааны хавчаар
Төмөр хөрөөТөмөр хөрөө
Тохируулгатай түлхүүрТохируулгатай түлхүүр
8

Lever T, link U and rod V

Cut lever T from hardwood 40 x 70 mm, 1195 mm long. Bolt it to the front of the right upright, 610 mm above the stringer, free to rock. Join it to the crank pin by link U, hardwood 20 x 40 mm with its pin holes 560 mm apart, 715 mm from T's pivot. At T's left end join rod V, hardwood 30 x 40 mm, slotted 22 mm wide for 220 mm, and pass it through the left upright's opening astride pin v. Fix a steel pin 3, 24 mm and 370 mm long, through T 1015 mm from its pivot, sticking out at the front for the churn.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз2 ширхэг
Зургаан талт болтны цуглуулгаЗургаан талт болтны цуглуулга4 ширхэг
Хавтгай угаагуурХавтгай угаагуур8 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка4 ширхэг
Зэвэрдэггүй ган савааЗэвэрдэггүй ган саваа1 ширхэг

Шаардлагатай багаж:

Ширээний хөрөөШирээний хөрөө
Гар фрезерГар фрезер
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Хүрзэн өрмийн үзүүрийн багцХүрзэн өрмийн үзүүрийн багц
Төмөр хөрөөТөмөр хөрөө
Элсэн цаасЭлсэн цаас
Тохируулгатай түлхүүрТохируулгатай түлхүүр
Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
9

Spring beam W and the pounder

Cut the spring beam W from ash 30 x 40 mm, 1210 mm long. Lay it on T's top, its left end against a block glued on T, bolt it through T 415 mm left of the pivot with a wing nut (the hand nut w), and let it run past the upright to overhang the frame by 510 mm. Make rod X from hardwood 40 x 40 mm, 1090 mm long, with four holes at its top for height. Under it glue a hardwood head 200 x 120 mm with five legs 30 x 36 mm, 160 mm long, each slotted (Z) and bored across (z). Hang X from W's end on a bolt so it swings freely, in front of W.

Энэ алхмын материал:

Хаданмодны банзХаданмодны банз1 ширхэг
Хатуу модон банзХатуу модон банз1 ширхэг
Модны цавууМодны цавуу1 ширхэг
Зургаан талт болтны цуглуулгаЗургаан талт болтны цуглуулга2 ширхэг
Эрвээхэй гайкаЭрвээхэй гайка1 ширхэг
Хавтгай угаагуурХавтгай угаагуур4 ширхэг

Шаардлагатай багаж:

Ширээний хөрөөШирээний хөрөө
Гар фрезерГар фрезер
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Ховилын цүүцХовилын цүүц
Модон алхМодон алх
Элсэн цаасЭлсэн цаас
Савааны хавчаарСавааны хавчаар
10

Hinged platform M, bevel wheels and platform K

Make platform M from 40 mm hardwood, 860 x 860 mm, and hang it on two strap hinges (the butts m) at the feet of the right-hand legs. On M, 100 mm from the hinges, fit a 20 mm vertical shaft in a flange bearing with pulley R and the lower bevel wheel on it. In a hardwood post fit a 20 mm cross shaft with the upper bevel wheel and a 240 mm hardwood pulley P in line with the pulley on D. 480 mm from the hinges, 340 mm towards the front, set a 24 mm shaft L in a hardwood block that slides in a slot along M, with a compression spring pushing it away from R. Glue platform K, 660 mm across and 40 mm thick, bore it for L, and set four 40 mm hardwood wheels l under its edge.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз4 ширхэг
Модны цавууМодны цавуу1 ширхэг
Төмөр урт нугасТөмөр урт нугас2 ширхэг
Фланцтай холхивчФланцтай холхивч3 ширхэг
Конус шүдтэй хүрдний багц (ган, 1:1)Конус шүдтэй хүрдний багц (ган, 1:1)1 ширхэг
Зэвэрдэггүй ган савааЗэвэрдэггүй ган саваа1 ширхэг
Shaft CollarShaft Collar3 ширхэг
Шахалтын пүршний багцШахалтын пүршний багц1 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг
Модны шурагМодны шураг40 ширхэг
Зургаан талт болтны цуглуулгаЗургаан талт болтны цуглуулга4 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка4 ширхэг
PETG филаментPETG филамент1 ширхэг

Шаардлагатай багаж:

FDM 3D хэвлэгчFDM 3D хэвлэгч
Хөрөө (лобзик)Хөрөө (лобзик)
Луужин (компас)Луужин (компас)
Гар фрезерГар фрезер
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Хүрзэн өрмийн үзүүрийн багцХүрзэн өрмийн үзүүрийн багц
Төмөр хөрөөТөмөр хөрөө
Савааны хавчаарСавааны хавчаар
Тохируулгатай түлхүүрТохируулгатай түлхүүр
11

Belts O and S, and the fold

Put belt S round pulley R and platform K's rim. Fold M up against the frame, run a string round the pulley on D and pulley P, and choose belt O just short enough that, with M let down and empty, it holds M at a slight angle; "The belt O is sufficiently short to hold the platform M at a slight angle until the weight of J is added thereto." Set the wooden tub J on K: its weight should pull M flat and the belt tight. Oil the wood.

Энэ алхмын материал:

Хөтлөх бүсХөтлөх бүс2 ширхэг
Модон тэвшМодон тэвш1 ширхэг
Буцалгасан маалингын тосБуцалгасан маалингын тос1 ширхэг

Шаардлагатай багаж:

Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
12

The build in 3D

FreeCAD model of this build: the frame, shaft D with the balance wheel and crank E, lever T with link U and rod V, the spring beam W and the pounder in the tub (front of the tub cut away), the hinged platform M with the bevel wheels, pulleys and belts, and the churn on pin 3. The crank was turned through 18 positions.
Дизайны файлBLENDCC0 - Free
13

Wash

Put warm water, soap and the clothes in the tub, and set the pounder's height so its feet clear the tub's bottom by the clothes. Turn the hand crank steadily. The pounder rises and falls on one side of the tub while the tub turns under it, so every part of the wash comes under it in turn. Move the crank pin out in its slot for a longer stroke, in for a shorter one. Lift the clothes out to rinse and wring.

Шаардлагатай багаж:

УсУс
Саван хэрчимСаван хэрчим
14

Churn on pin 3

Make the dash 2: a hardwood rod 35 mm across, 1250 mm long, bored at the top to hang on pin 3, with two crossed blades 220 x 30 x 20 mm at the bottom. Stand the churn under pin 3, beside the machine, pour in about 10 litres of cream at about 15 °C (checked with the thermometer), a third of its height, pass the dash through the lid and hang it on pin 3. Turn the crank, with or without the wash, timing it. When the butter comes, lift the dash off the pin, drain the buttermilk, wash the butter in cold water, salt and weigh it.

Энэ алхмын материал:

Өтгөн цөцгийӨтгөн цөцгий10 l
Бүдүүн далайн давсБүдүүн далайн давс1 ширхэг
Хатуу модон банзХатуу модон банз1 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг

Шаардлагатай багаж:

Цөцгийн тос бүлэх савЦөцгийн тос бүлэх сав
Дотор нь үлдээдэг мэдрэгчтэй термометрДотор нь үлдээдэг мэдрэгчтэй термометр
Секунд хэмжигчСекунд хэмжигч
Дижитал гал тогооны жинДижитал гал тогооны жин
Зэвэрдэггүй ган том хольц аягаЗэвэрдэггүй ган том хольц аяга
УсУс
Утасгүй өрөмУтасгүй өрөм
Хүрзэн өрмийн үзүүрийн багцХүрзэн өрмийн үзүүрийн багц
Гар хөрөөГар хөрөө
15

Troubleshooting

Washing machine troubleshooting.

Flow

Loading...
16

History and honest limits

**John Wagoner and Abram Severson, Jr.** of Guilderland Center, New York, US 25,152, 16 August 1859, "Washing-Machine". They claimed mounting the platform K and the pulleys and gearing P Q R on the hinged platform M, so turning M up slackens belt O and turning it down lets the tub's weight tighten it. The patent gives no sizes; every size here is ours. Their hand lever H and rod I, a second way to turn D, are not built: we turn D by a crank, which the patent allows. The spring that urges K's centre against belt S is "not represented" in their drawing; ours is a compression spring in a slot.

Материал

24

Шаардлагатай багаж

24

Загварын файлууд

3

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...