Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ

Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)
C. H. Willey's quick-acting vise for the drill-press table (Popular Mechanics, 1920): a 1/2 x 3 in. steel bed drilled with 5/8 in. holes 7/8 in. apart and bolted down on slotted end pieces, a fixed jaw pinned into any hole, a sliding jaw kept on the bar by a riveted cross pin, and an eccentric cam on a handle that locks the work.
Дунд шат
A day
Зааварчилгаа
1
1
The steps
The steps
Jupyter дэвтэр ачаалж байна…
2
2
Read Willey
Read Willey
"A very efficient, quick-opening and closing vise for the drill-press table."
3
3
Make the bed
Make the bed
Cut a bed bar from 1/2 x 3 in. (13 x 76 mm) steel to suit your table (length ours). Drill a row of 5/8 in. (16 mm) holes 7/8 in. (22 mm) apart along its middle.
Энэ алхмын материал:
Зөөлөн ганы хавтгай туйван1 ширхэгШаардлагатай багаж:
Төмөр хөрөө
Төвлүүлэх цүүц
Суурин өрөм
Өрмийн үзүүрийн иж бүрдэл4
4
Make the end supports
Make the end supports
Cut two short pieces of the same stock, slot them for bolts to the drill-press table and fix one under each end of the bed (ours: bolted), so the bed stands clear of the table.
Энэ алхмын материал:
Зөөлөн ганы хавтгай туйван1 ширхэг
Зургаан талт болтны цуглуулга1 ширхэгШаардлагатай багаж:
Төмөр хөрөө
Суурин өрөм
Өрмийн үзүүрийн иж бүрдэл
Дүрд (гар дүрд)5
5
Make the fixed jaw
Make the fixed jaw
Cut out a steel block underneath so it straddles the bed (stock and size ours). Drive a pin into it, downward, that fits the 5/8 in. holes.
Энэ алхмын материал:
Зөөлөн ганы хавтгай туйван1 ширхэг
Зөөлөн ганан дугуй баганз1 ширхэгШаардлагатай багаж:
Төмөр хөрөө
Дүрд (гар дүрд)
Суурин өрөм
Өрмийн үзүүрийн иж бүрдэл
Бөмбөрцөг толгойт алх6
6
Make the sliding jaw
Make the sliding jaw
Cut a second block the same way. Pass a horizontal pin across the opening below the bed and rivet it to the jaw's sides, so the jaw slides along the bar but cannot lift off.
Энэ алхмын материал:
Зөөлөн ганы хавтгай туйван1 ширхэг
Зөөлөн ганан дугуй баганз1 ширхэгШаардлагатай багаж:
Төмөр хөрөө
Дүрд (гар дүрд)
Суурин өрөм
Өрмийн үзүүрийн иж бүрдэл
Бөмбөрцөг толгойт алх
Ширээний хавчаар7
7
Make the cam
Make the cam
Saw a disk off steel shafting. Drive a pin that fits the 5/8 in. holes into one face, off centre. At right angles to it, drill a hole in the rim and fit a handle.
Энэ алхмын материал:
Ган гол1 ширхэг
Зөөлөн ганан дугуй баганз1 ширхэгШаардлагатай багаж:
Төмөр хөрөө
Суурин өрөм
Өрмийн үзүүрийн иж бүрдэл
Бөмбөрцөг толгойт алх8
8
Use it
Use it
Bolt the bed to the table. Set the fixed jaw's pin in the hole that suits the work, slide the jaw up, drop the cam pin into the hole behind it and swing the handle to lock the work.
Энэ алхмын материал:
Зургаан талт болтны цуглуулга1 ширхэгШаардлагатай багаж:
Суурин өрөм9
9
Troubleshooting
Troubleshooting
Drill vise troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
From C. H. Willey, "A Simple Drill Vise", **Popular Mechanics** vol. 34 (November 1920), p. 3340 (checked on the archive.org scan of Popular Mechanics Shop Notes, popularmechanic00unkngoog). He gives only the bed section and the hole size and spacing; jaw and cam sizes, the bar length, how the end pieces are fixed and the cam offset are ours.
Материал
4- 1 ширхэгТүр орлуулагч
- 2 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
Энэ загвараар хийдэг
Холбоотой загварууд
Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим
CC0 Нийтийн домэйн
Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.
Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.


