Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ

Woodworking Saw: a Hand Saw Made the Disston Works Way (1922)
A hand saw for wood is a toothed steel blade with a wooden handle. Henry Disston & Sons of Philadelphia, who made most of the hand saws used in the United States, described their own sequence in a 1922 booklet: shear the plate, tooth it, harden and temper it, hammer it flat and true, grind it thinner toward the back and the point, tension it, polish it, set and file the teeth, and screw on a fitted handle.
The booklet gives the order of the work and how the hand work is done, but keeps its numbers to itself: the steel, the hardening heat and bath, the tempering and the stiffening were Disston secrets. Those gaps are marked as unknown below.
Source: How a Disston Hand Saw Is Made (Henry Disston & Sons, 1922), pp. 1-9. Picture: their p. 8, setting and filing.
Дээд шат
Several days
Зааварчилгаа
1
1
Read Disston
Read Disston
"To the uninitiated, a hand saw represents simply a notched piece of sheet steel, with a wooden handle on one end. As a matter of fact, there are more than 82 progressive operations in making a Disston Hand Saw."
2
2
Cut and tooth the plate
Cut and tooth the plate
Disston made its own steel from special formulas, cast it into ingots and rolled them red hot into sheets; the grade and thickness are not given, so start from steel sheet. Shear the sheet to the shape and size of the blade. Heavier plates are kept for coarse teeth and lighter ones for fine. Stamp the blade with the number of points (teeth) to the inch it is to have, then punch the teeth in a toothing machine. The blade is still soft.
Энэ алхмын материал:
Ган хуудас1 ширхэгШаардлагатай багаж:
Цоолох шахуурга
Хамгаалалтын нүдний шил3
3
Harden and temper
Harden and temper
Heat the toothed blade evenly in an oil-burning furnace to its hardening heat, then plunge it edge first into the hardening bath. It is now extremely hard and brittle, so handle it with great care until it is tempered. Tempering draws back part of that hardness and gives the blade its spring. Disston does not give the heat, the bath or its tempering process (unknown).
Шаардлагатай багаж:
Түлшний тосоор халдаг зуух
Тодорхойгүй материал
Хамгаалалтын нүдний шил4
4
Smith it flat
Smith it flat
Hammer the blade on the anvil to straighten and flatten it ("smithing in the black"). Lift it and sight along it toward the light: the shadows on the blade show where the hammer should fall. Work by daylight; Disston found that wavering artificial light would not do.
Шаардлагатай багаж:
Алх
Дөш5
5
Taper-grind
Taper-grind
Grind the blade to its gauge, and taper it: it gets thinner from the tooth edge to the back, and from the handle to the point, while the tooth edge stays the same thickness from end to end. Disston: "A saw not ground to proper taper cannot be ranked a high-class tool."
Шаардлагатай багаж:
Зүлгүүрийн дугуй
Хамгаалалтын нүдний шил6
6
Tension the blade
Tension the blade
Hammer the blade again to give it the right tension, so that it is neither "fast" nor "loose". In a fast blade the metal is too long at the edge: hammer the centre to expand it. In a loose blade, stretch the edge. A saw without proper tension will not cut straight and true, and will buckle in the wood.
Шаардлагатай багаж:
Алх
Дөш7
7
Draw-grind, glaze, block and polish
Draw-grind, glaze, block and polish
Grind the blade a second time ("draw-grinding") to prepare it for polishing. Glaze it by buffing while it is covered with very fine emery. Then "block" it: hammer out any small irregularities left by grinding and glazing, on the anvil and on a block of lignum vitae, a wood hard enough to work on but which leaves no hammer marks. Polish the blade. Disston then stiffened it by a process it kept secret, and etched its mark on it.
Шаардлагатай багаж:
Зүлгүүрийн дугуй
Зүлгүүрийн (эмери) нунтаг
Алх
Дөш
Хатуу модон банз8
8
Set the teeth
Set the teeth
Lay the blade on the setting block, or stake. Starting with the first tooth at the butt end, set every other tooth; then turn the blade over and, starting with the first unset tooth at the point, set the rest. Use a hammer with a long, tapering head: one tap sets each tooth over by half the blade's thickness, so the cutting edge is about twice as thick as the blade. This keeps the saw from binding.
Шаардлагатай багаж:
Алх
Дөш9
9
Sharpen
Sharpen
Clamp the saw in a vise and, holding the file in both hands, go from tooth to tooth, giving each tooth its bevel and a keen edge.
Шаардлагатай багаж:
Ширээний хавчаар
Хөрөөний шүдний дэгэц10
10
Fit the handle
Fit the handle
Cut and bore a wooden handle and fit it to its own blade, so the saw has the right "hang" (pitch) in use; the kind of wood is not given (unknown). Put the handle on the blade, mark the screw holes with a scriber, take the handle off and punch the holes in the blade. Replace the handle and fasten it with brass saw screws. Look the saw over for faults, then oil it and wipe it off; the oil is not named (unknown).
Энэ алхмын материал:
Хөрөөдсөн банз1 ширхэг
Хөрөөний шураг1 багц
Тодорхойгүй материал1 dashШаардлагатай багаж:
Муруй хөрөө
Суурин өрөм
Зурмал зүү
Цоолох шахуурга
Хөвөн өөдөс11
11
History and honest limits
History and honest limits
Henry Disston began making hand saws in Philadelphia in 1840, without even a helper, and made his own steel from 1855. By 1922 the works employed about 3,600 people, sawed its handle wood from logs in its own mill and made its own brass screws.
The booklet was written for customers, not saw makers. It leaves out every number: steel, thickness, points per inch, hardening heat and bath, tempering and stiffening. Those are marked unknown here, and the use of a punch press, a grinding wheel, a coping saw and a drill press for the factory machines is ours.
Материал
4- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 багцТүр орлуулагч
- 1 dashТүр орлуулагч
Шаардлагатай багаж
15- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
Энэ загвараар хийдэг
Холбоотой загварууд
Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим
CC0 Нийтийн домэйн
Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.
Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

