ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE

The Collapsible Tube: A Container That Is Always Full
Before the 1840s a painter kept ground oil colour in pig's bladders tied with string, pricked to squeeze some out; once opened, the paint began to dry. A tube of soft metal, squeezed from the end and capped, keeps the rest sealed from the air.
US 2,252, dated 11 September 1841, was granted to John Rand, then living at Howland Street, Middlesex, England — the American portrait painter John Goffe Rand. Its drawing sheet is titled "Metal Rolls for Paint". Tubes of grain-tin, lead or pewter thin enough "to be caused to be permanently collapsed" are filled, closed at both ends, pierced or fitted with a screw-capped nozzle, and rolled up from the end as the paint is used.
This rung works out why a soft metal tube stays collapsed, and fills and tests tubes of paint.
Principiante
About 2 hours
Instrucciones
1
1
Dose per millimetre and fold strain
Dose per millimetre and fold strain
Cargando el cuaderno de Jupyter…
2
2
Why paint must be kept from the air
Why paint must be kept from the air
Oil paint cures by reacting with oxygen. The embedded blueprint explains the drying mechanisms that a sealed tube stops.
3
3
Read US 2,252
Read US 2,252
Rand's invention relates to "a mode of preserving paints and other fluids by confining them in close metallic vessels so constructed as to collapse with slight pressure, and thus force out the paint or fluid confined therein through proper openings", which can then be closed air-tight. The vessels are "at all times full, whatever be the quantity of fluid matter remaining therein".
He names "grain-tin, lead, and pewter" as the best and cheapest metals, of such thickness "as readily to yield to pressure and to be caused to be permanently collapsed". Fig. 1's vessel is "made of grain-tin drawn into a tube", the metal "about one seventy-fifth of an inch in thickness", its ends closed by melting the pressed edges or by soldering; a pair of forceps b holds the end for closing it with a blowpipe or hot iron.
A hole is made at c and "it is better that the pressure should be made at the end, d, of the vessel", so the collapsed end "may be rolled up". Fig. 4 adds a short tube with "a screw-cap". He warns that the fluid must not be one "chemically prejudicially acted on by the metal employed".
4
4
Fill tubes and test the seal
Fill tubes and test the seal
Mix a little oil paint from the set with a few drops of linseed oil. Fill two empty paint tubes from the open end with a palette knife, fold the end over twice with flat-nose pliers and crimp it flat. Put the same paint in a small open-topped jar with a loose lid.
Each day for a week, squeeze a pea of paint from a tube and rolling up the end, and take a pea from the jar. Note when the jar's paint grows a skin and when the tube's does. Measure the flattened length per squeeze with the caliper and compare with the notebook's millimetres per millilitre.
Materiales para este paso:
Tubos de pintura vacíos2 piezas
Juego de pinturas al óleo1 pieza
Aceite de linaza1 pieza
Tarro de vidrio1 piezaHerramientas necesarias:
Alicates de boca plana
Calibre digital de 6 pulgadas
Cúter de precisión5
5
A tube that dries out or leaks
A tube that dries out or leaks
Collapsible tube troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**US 2,252**, dated 11 September 1841, was granted to **John Rand**, a citizen of the United States then living in Middlesex, England; he is the portrait painter John Goffe Rand. It claims the mode of preserving paint in vessels that collapse by slight pressure as their contents are removed.
**Honest limits.** Tin's modulus and yield stress in the notebook are typical values; lead and pewter behave similarly. Lead tubes are not used for food or cosmetics today.
Materiales
4- 2 piezasMarcador de posición
- Juego de pinturas al óleo10% de comisión1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
Herramientas requeridas
3- Marcador de posición
- Marcador de posición
- Marcador de posición
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios

Extracting Tin from Cassiterite — Smelting the Bronze Alloying Metal
por Forge
Trabajo en Metal
92
0
0
0
0
0

Drawing Wire Through a Drawplate — Reducing Iron Rod to Fine Wire
por Forge
Trabajo en Metal
48
0
0
0
3
0

Making Azurite Blue Pigment — Grinding the Copper Mineral into the Blue of Medieval Painting
por Charlie
ARTE
69
0
0
0
4
0

Drying Is Not Evaporating: Three Different Mechanisms, Three Different Films
por Mary
Química
25
0
0
0
0
0
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.